manualshive.com logo in svg

Cisco 10008, Руководство по установке и настройке, Страница: 27 / 70

Поделиться
Скачать
Cisco 10008 Скачать руководство пользователя страница 27

27

Cisco 10008 Router PRE4 Installation and Configuration Guide

OL-13840-01

  Upgrading a PRE3 to a PRE4

Upgrading a PRE3 to a PRE4 

This section describes the following procedures to perform a hardware upgrade from a PRE3 to a PRE4: 

•

Upgrading a PRE3 to a PRE4 Using ISU, page 27

•

Upgrading a PRE3 to a PRE4 Without Using ISU, page 29

You can upgrade a PRE3 to a PRE4 using the In Service Upgrade (ISU) feature. A PRE3 to PRE4 ISU 
is non-service impacting. Powering down the router is not required. 

A PRE3 to PRE4 upgrade without ISU is a service impacting upgrade. The router is not available for 
user traffic during the upgrade, and traffic cannot resume until the upgrade is complete.

Upgrading a PRE3 to a PRE4 Using ISU 

This section describes the procedure to perform a PRE3 to PRE4 upgrade using the ISU feature: 

•

Prerequisites, page 27

•

Upgrade Considerations, page 27

•

Procedure to Upgrade a PRE3 to a PRE4 Using ISU, page 28

Prerequisites

•

For all of the software features supported by your current PRE3 (c10k3-p11-mz) image to function 
correctly, they must be supported by the PRE4 image. Check with the Cisco Technical Assistance 
Center (TAC) to verify the correct upgrade path before initiating the upgrade.

•

The upgrade should be performed by a qualified engineer. This person must be familiar with the 
Cisco router console interface and be able to perform basic router operations, such as configuration 
loading and router reload functions.

•

Do not perform this upgrade if your current PRE3 software image supports new features not yet 
supported by the PRE4 software image. Performing this upgrade will cause these features to fail.

•

Stateful Switchover (SSO) must be configured and working properly. If you do not have SSO 
enabled, see the 

Stateful Switchover 

document for further information on how to enable and 

configure SSO. 

•

The Cisco IOS software release on the PRE3 must be the same Cisco IOS software release that is 
on the PRE4. For information on how to perform full image software upgrades using the In Service 
Software Upgrade (ISSU) process, see the 

Cisco IOS In Service Software Upgrade and Enhanced Fast 

Software Upgrade Process

 publication.

Upgrade Considerations

•

The SPA interface processors (SIPs) reset during a PRE3 to PRE4 ISU. 

•

If the Cisco IOS software release on the PRE4 is compatible with the software release on the PRE3, 
the system operates in Stateful Switchover (SSO) mode. If the images are not compatible, the system 
operates in route processor redundancy (RPR) mode. 

•

We recommend that you copy the new Cisco IOS software release for the PRE4 on a separate system, 
and not on the system you are upgrading. 

Содержание 10008







































































Отзывы:

Нет отзывов