Cisco 10008 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 70

Cisco 10008 Скачать руководство пользователя страница 42

42

Cisco 10008 Router PRE4 Installation and Configuration Guide

OL-13840-01

Analyzing and Troubleshooting Packets

Router#

show pxf cpu statistics security

ACL Pkts Pkts Denied Permit Other

Name Denied Permitted & Log & Log Packets

108 0 0 0 0 0

The following example output results after sending the 100 packets. Notice that the Packets Denied field
now indicates that 100 packets have been denied. Recall that the router denied the packets because they
matched the implicit deny statement. This statement does not include a

log

keyword, which causes

information to be sent to the console. Therefore, no logging occurs and the Denied and Log fields
indicate this.

Router#

show pxf cpu statistics security

ACL Pkts Pkts Denied Permit Other

Name Denied Permitted & Log & Log Packets

108 100 0 0 0 0

Displaying IP Forwarding Statistics

The

show pxf cpu statistics ip

command provides statistical information about IP forwarding. The

following example output indicates that the count of the IP forwarding counter before sending the 100
packets is 402.

Router#

show pxf cpu statistics ip

FP ip statistics

dropped = 0

forwarded = 402

punted = 540

input_packets = 942

icmps_created = 0

noadjacency = 0

noroute = 6

unicast_rpf = 0

FP ip multicast statistics

mcast total = 0

mcast drops = 0

mcast punts = 0

mcast switched = 0

mcast encaps = 0

mcast decaps = 0

FP ip frag statistics

packets = 0

fragments = 0

fragfail = 0

dontfrag = 0

mcdontfrag = 0

FP icmp statistics

unreachsent = 2

ttlsent = 0

echorepsent = 5

echorcv = 5

checksumerr = 0

FP mpls statistics

diverted = 0

dropped = 0

switched = 0

«
...
40
41
42
43
44
...
»

Содержание 10008







































































Отзывы:

Нет отзывов