background image

VCC-FM60FV19CL  

Rev. 

900-714-31-00 

©2011 CIS Corporation. All rights reserved. 

27 

 

15.

 

Cases for Indemnity (Limited Warranty) 

 

We shall be exempted from taking responsibility and held harmless for damage or losses incurred by 
the user in the following cases. 
 

z

 

  In case damage or losses are caused by fire, earthquake, or other acts of God, acts by third party, 

deliberate or accidental misuse by the user, or use under extreme operating conditions. 

z

 

  In case indirect, additional, consequential damages (loss of business interests, suspension of 

business activities) are incurred as result of malfunction or non-function of the equipment, we 
shall be exempted from responsibility for such damages. 

z

 

  In case damage or losses are caused by failure to observe the information contained in the 

instructions in this product specification & operation manual. 

z

 

  In case damage or losses are caused by use contrary to the instructions in this product 

specification & operation manual. 

z

 

  In case damage or losses are caused by malfunction or other problems resulting from use of 

equipment or software that is not specified. 

z

 

  In case damage or losses are caused by repair or modification conducted by the customer or any 

unauthorized  
third party (such as an unauthorized service representative). 

z

 

  Expenses we bear on this product shall be limited to the individual price of the product. 

 

16.

 

CCD Pixel Defect 

CIS compensates the noticeable CCD pixel defects found at the shipping inspection prior to our 
shipment.    On very rare occasions, however, CCD pixel defects might be noted with time of usage of 
the products. 
Cause of the CCD pixel defects is the characteristic phenomenon of CCD itself and CIS is exempted 
from taking any responsibilities for them.    Should you have any questions on CCD pixel defects 
compensation, please contact us. 
 

17.

 

Product Support 

 

When defects or malfunction of our products occur, and if you would like us to investigate on the 
cause and repair, please contact your distributors you purchased from to consult and coordinate.   

 

Содержание VISION:elite VCC-FM60FV19CL




























Отзывы: