CIS VISION:elite VCC-FM60FV19CL Скачать руководство пользователя страница 18

Страница: 18 / 27

VCC-FM60FV19CL

Rev.

900-714-31-00

Remote Communication Function

Via camera link cable, the camera can be controlled.

(1)

The settings for RS232C

(2)

Control code

・

The total control code is 14 bytes, which conforms to ASCII code.

・

The control code consists of camera No. process code, remote controller address, remote
controller data, and CR. Execute Read/Write through PC, and the camera will reply the data.

1 2 3 4 5 6

7th

Byte

8 9 10

Camera No.

Process code

Remote controller

address

Remote controller data

000000: fixed

“R” Read mode

Please refer to the

address table of Section

5. Function Settings.

000

～

255

0 Dh

“W” Write mode

“C” Camera mode

Camera No. is fixed with 6 bytes numerical strings, “000000”.

Process code

Input any one of R, W, or C to the process code.

R (read mode) is to read the data of remote controller address.
Please be noted to set any dummy data (000

～

255) to 11

～

, since a command shall

consists of 14 bytes.

W (write mode) is to write the data to the remote controller address.

Please be noted that the data cannot be saved into EEPROM of the camera.

(Reboot the camera, and the data is reset to the initial setting.)

To save the data into EEPROM, please refer to Section 5. Function Settings.

C is the code to send the data back from the camera.

Note: Do not set code C when sending the data from PC side.

Baud rate

9600bps

Data :

8bit

Stop bit

1bit

Parity :

None

XON/XOFF :

Not controlled

Содержание VISION:elite VCC-FM60FV19CL



























Результаты поиска

Содержание VISION:elite VCC-FM60FV19CL

Отзывы:

Похожие инструкции для VISION:elite VCC-FM60FV19CL

Бренды по названию

Популярные бренды

CIS VISION:elite VCC-FM60FV19CL, Техническое описание и руководство по эксплуатации

Результаты поиска

Содержание VISION:elite VCC-FM60FV19CL

Отзывы:

Похожие инструкции для VISION:elite VCC-FM60FV19CL

Бренды по названию

Популярные бренды