background image

  VCC-5CXP3R   

 

Rev. 905-0052-00 

©2016 CIS Corporation. All rights reserved. 

10 

 

Notes for the delay time for trigger pulse and exposure start 
Due to the image sensor’s features, there will be a difference between normal readout operation (exposure for next frame 
starts after readout has completed) and overlapping readout operation (exposure for next frame starts while readout.) There 
should be some gap of timing when trigger has input to image sensor, and the actual timing that exposure starts. 
 

At

 

full pixel operation (ROI_OFF) 

 

Link Rate 

CXP1 

CXP2 

CXP3 

CXP5 

CXP6 

Exposure delay at normal readout [µs] 

Please refer to Exposure delay time (A) in the   

timing chart below. 

Exposure delay at overlapping [µs] 

Please refer to Exposure delay time (B) in the   
timing chart below. 

26-49 

19-31 

19-31 

9-15 

9-15 

 

At

 

operation with sub-sampling function 

 

Link Rate 

CXP1 

CXP2 

CXP3 

CXP5 

CXP6 

Exposure delay at normal readout [µs] 

Please refer to Exposure delay time (A) in the   

timing chart below. 

Exposure delay at normal readout [µs] 

Please refer to Exposure delay time (A) in the   

timing chart below.

 

18-34 

14-22 

14-22 

7-11 

7-11 

 

  Delay time will depend on the settings of frame rate and exposure time, but will not fluctuate in a fixed condition.     

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Aegis Electronic Group, Inc.

Содержание VCC-5CXP3R

































Отзывы: