background image

 M039150CF

6

BURNER FEATURES

Burner model identification

Burners are identified by burner type and model. Burner model identification is described as follows.

Technical specifications   

Type

 

HP72

     

Model

   

MG.    AB.

  S.

*.

A.

0.

40

(1)

   (2)

   (3)

 (4)

 (5)

(6)       (7)         (8)

(1) 

BURNER TYPE

HP72

(2)

FUEL

 

M - 

Natural gas

               G - 

Light oil

(3)

OPERATION

  (

Available versions

()

AB  - 

Double stage

(4) 

BLAST TUBE

S - 

standard

(5) 

DESTINATION COUNTRY

* -  Destination countrysee data plate

(6) 

BURNER VERSION

A - Standard

(7)

EQUIPMENT

0 = 

2 gas valves

1 = 

2 gas gas proving system

7 = 

2 gas maximum gas pressure switch

8 = 

2 gas gas proving maximum gas pressure switch

(8)

GAS CONNECTIONS

40 = Rp11/2              50 = Rp2             65 = DN65            80 = DN80

BURNER TYPE

HP60 MG....40

HP60 MG....50/65

HP65 MG.....50/65

Output

min. - max.kW

170 - 523

170 - 880

270-970

Fuel

Nat. gas - Light oil

Gas category

(see next paragraph)

Gas rate

min. - max. (Stm

3

/h)

18 - 55

18 - 93

29-103

Gas pressure

min. - max. mbar

(see Note 2)

Light oil rate

min. - max. kg/h

14 - 44

14 - 74

23-82

Light oil train inlet pressure 

max. bar

2

Oil viscosity 

2 - 7.4 cSt @ 40°C

Oil density 

840 kg/m3

Power supply

400V 3N ~  50Hz

Total power consumption

kW

2.15

2.15

2.55

Electric motor

kW

1.1

1.1

1.5

Pump motor

kW

0.55

0.55

0.55

Protection

IP40

Approx. weight

kg

65

72

107

Operation

Double-stage

Gas Train

40

50 - 65

50 - 65

Valves size/Gas connection

1”

1/2 

/ Rp1

1/2

2” /Rp2 - 2”

1/2 

/DN65

2” /Rp2 - 2”

1/2 

/DN65

Operating temperature

°C

-10 ÷ +50

Storage Temperature

°C

-20 ÷ +60

Working service*

Intermitent

BURNER TYPE

HP72 MG....0.50

HP72 MG.....0.65

HP72 MG....0.80

Output

min. - max.kW

330 - 1200

Fuel

Nat. gas - Light oil

Gas category

(see next paragraph)

Gas rate

min. - max. (Stm

3

/h)

35 - 127

Gas pressure.

min. - max. mbar

(see Note 2)

Light oil rate

min. - max. kg/h

28 - 101

Light oil train inlet pressure 

max. bar

2

Oil viscosity 

2 - 7.4 cSt @ 40°C

Oil density 

840 kg/m3

Power supply

400V 3N ~  50Hz

Total power consumption

kW

3.25

Electric motor

kW

2.2

Pump motor

kW

0.55

Protection

IP40

Approx. weight

kg

107

117

127

Operation

Double-stage

Gas Train

50

65

80

Valves size / Gas connection

2”/ Rp2

2”

1/2   

/ DN65

3”

  

/ DN80

Operating temperature

°C

-10 ÷ +50

Storage Temperature

°C

-20 ÷ +60

Working service*

Intermittent

PART I: INSTALLATION MANUAL

Содержание HP60 Series





















































Отзывы: