Chrysler pacifica hybrid 2017 Скачать руководство пользователя | Manualshive

Страница: 419 / 604

background image

•

The Sealant Bottle is a one tire application use and needs
to be replaced after each use. Always replace these
components immediately at your original equipment
vehicle dealer.

•

When the Tire Service Kit sealant is in a liquid form,
clean water, and a damp cloth will remove the material
from the vehicle or tire and wheel components. Once the
sealant dries, it can easily be peeled off and properly
discarded.

•

For optimum performance, make sure the valve stem on
the wheel is free of debris before connecting the Tire
Service Kit.

•

You can use the Tire Service Kit air pump to inflate
bicycle tires. The kit also comes with two needles,
located in the Accessory Storage Compartment (on the
bottom of the air pump) for inflating sport balls, rafts, or
similar inflatable items. However, use only the Air Pump
and make sure the Mode Select Knob is in the Air Mode
when inflating such items to avoid injecting sealant into
them. The Tire Service Kit Sealant is only intended to
seal punctures less than 1/4 inch (6 mm) diameter in the
tread of your vehicle.

•

Do not lift or carry the Tire Service Kit by the hoses.

WARNING!

•

Do not attempt to seal a tire on the side of the vehicle
closest to traffic. Pull far enough off the road to avoid
the danger of being hit when using the Tire Service Kit.

•

Do not use Tire Service Kit or drive the vehicle under
the following circumstances:

– If the puncture in the tire tread is approximately

1/4 inch (6 mm) or larger.

– If the tire has any sidewall damage.
– If the tire has any damage from driving with

extremely low tire pressure.

– If the tire has any damage from driving on a flat tire.
– If the wheel has any damage.
– If you are unsure of the condition of the tire or the

wheel.

•

Keep Tire Service Kit away from open flames or heat
source.

•

A loose Tire Service Kit thrown forward in a collision
or hard stop could endanger the occupants of the
vehicle. Always stow the Tire Service Kit in the place
provided. Failure to follow these warnings can result
in injuries that are serious or fatal to you, your
passengers, and others around you.

(Continued)

7

IN CASE OF EMERGENCY

417

«
...
417
418
419
420
421
...
»

Содержание pacifica hybrid 2017





























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для pacifica hybrid 2017

Бренд: Mazda Страницы: 4

Бренд: Ford Страницы: 38

2007 MazdaSpeed6

Бренд: Mazda Страницы: 12

Бренд: Gator Страницы: 2

Бренд: Nav TV Страницы: 4

Parrot MKi + ParrotCK3100 range LOGAN

Бренд: Parrot Страницы: 10

Бренд: AEM Страницы: 27

Akerstroms Tx700

Бренд: LXE Страницы: 146

Бренд: Gator Страницы: 6

Бренд: Kia Страницы: 58

K40 Platinum360

Бренд: K40 ELECTRONICS Страницы: 11

Бренд: Rydeen Страницы: 14

Бренд: Summit Racing Страницы: 11

2011 RDX Navigation System

Бренд: Acura Страницы: 16

Бренд: BMW Страницы: 64

Бренд: Uniden Страницы: 16

Turnoverball 1020

Бренд: Bowers & Wilkins Страницы: 6

Бренд: Mercedes-Benz Страницы: 284

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды