Chrysler pacifica hybrid 2017 Скачать руководство пользователя | Manualshive

Страница: 273 / 604

background image

4. Pull on the webbing to make the lap portion tight

against the child seat.

5. To lock the seat belt, pull down on the shoulder part of the

belt until you have pulled all the seat belt webbing out of
the retractor. Then, allow the webbing to retract back into
the retractor. As the webbing retracts, you will hear a
clicking sound. This means the seat belt is now in the
Automatic Locking mode.

6. Try to pull the webbing out of the retractor. If it is

locked, you should not be able to pull out any webbing.
If the retractor is not locked, repeat step 5.

7. Finally, pull up on any excess webbing to tighten the lap

portion around the child restraint while you push the child
restraint rearward and downward into the vehicle seat.

8. If the child restraint has a top tether strap and the

seating position has a top tether anchorage, connect the
tether strap to the anchorage and tighten the tether
strap. See the section “Installing Child Restraints Using
the Top Tether Anchorage” for directions to attach a
tether anchor.

9. Test that the child restraint is installed tightly by pulling

back and forth on the child seat at the belt path. It
should not move more than 1 inch (25.4 mm) in any
direction.

Any seat belt system will loosen with time, so check the
belt occasionally, and pull it tight if necessary.

Seat Belt Park Stitch — If Equipped

The rear outboard seat belts may be equipped with a park
stitch to raise the latch plate for easier access to occupants.
If the park stitch interferes with the tight installation of a
child restraint, slide the latch plate over the stitching to
shorten the lap portion of the belt and install the car seat
following the steps above. When the car seat is removed
from the vehicle, slide the latch plate above the park stitch
to enable occupants to latch the seatbelt securely.

Seat Belt Park Stitch Location

5

SAFETY

271

«
...
271
272
273
274
275
...
»

Содержание pacifica hybrid 2017





























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для pacifica hybrid 2017

PRIME DESIGN VCR 326

Бренд: Safe Fleet Страницы: 16

Prime Design VBC PC11

Бренд: Safe Fleet Страницы: 8

Prime Design AR1418

Бренд: Safe Fleet Страницы: 4

Бренд: Toyota Страницы: 56

Бренд: Parkeon Страницы: 43

Бренд: Toyota Страницы: 636

Бренд: Daesung Страницы: 9

Бренд: Pontiac Страницы: 318

Бренд: Bilstein Страницы: 7

Бренд: Webasto Страницы: 44

Бренд: Mazda Страницы: 604

Бренд: Kia Страницы: 25

Бренд: walser Страницы: 8

Бренд: Honda Страницы: 76

Бренд: Vauxhall Страницы: 310

Бренд: Whispbar Страницы: 17

Бренд: Truma Страницы: 84

Бренд: Intellitronix Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды