Chrysler pacifica hybrid 2017 Скачать руководство пользователя | Manualshive

Страница: 416 / 604

background image

2. Install the remaining lug nuts with the cone shaped end

of the nut toward the wheel. Lightly tighten the lug
nuts.

WARNING!

To avoid the risk of forcing the vehicle off the jack, do
not tighten the wheel nuts fully until the vehicle has
been lowered. Failure to follow this warning may
result in serious injury.

3. Lower the vehicle to the ground by turning the jack

handle counterclockwise.

4. Finish tightening the lug nuts. Push down on the

wrench while at the end of the handle for increased
leverage. Tighten the lug nuts in a star pattern until each
nut has been tightened twice. Refer to “Torque Specifi-
cations” in the “Technical Specifications” section for
proper wheel lug nut torque. If in doubt about the
correct tightness, have them checked with a torque
wrench by your authorized dealer or at a service station.

5. After 25 miles (40 km) check the lug nut torque with a

torque wrench to ensure that all lug nuts are properly
seated against the wheel.

TIRE SERVICE KIT — IF EQUIPPED

Your vehicle may be equipped with a Tire Service Kit.
Small punctures up to 1/4 inch (6 mm) in the tire tread can
be sealed with Tire Service Kit. Foreign objects (e.g., screws
or nails) should not be removed from the tire. Tire Service
Kit can be used in outside temperatures down to approxi-
mately -4°F (-20°C). This kit will provide a temporary tire
seal, allowing you to drive your vehicle up to 100 miles
(160 km) with a maximum speed of 50 mph (80 km/h).

414

IN CASE OF EMERGENCY

«
...
414
415
416
417
418
...
»

Содержание pacifica hybrid 2017





























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для pacifica hybrid 2017

Бренд: Camcar Страницы: 6

BLACK STEEL S2560

Бренд: Fab Fours Страницы: 9

Gasoline/Electric DS Golf Car 1996

Бренд: Club Car Страницы: 48

Бренд: Trailboss Страницы: 8

MAGNUM RT Series

Бренд: Raptor Series Страницы: 6

v.LOGiC Intelligent Solution V5-NTG46

Бренд: Caraudio-Systems Страницы: 18

DELTA DL FIX 209FP

Бренд: Menabo Страницы: 8

Бренд: Baja Designs Страницы: 5

RUDDER ANGLE INDICATOR

Бренд: VDO Страницы: 8

Бренд: Chevrolet Страницы: 372

Бренд: Hama Страницы: 4

Бренд: Volvo Страницы: 230

Бренд: Belkin Страницы: 2

Бренд: Enduro Страницы: 52

Бренд: Volvo Страницы: 92

Бренд: Connects2 Страницы: 2

Бренд: TracRac Страницы: 6

Бренд: LaserLine Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды