Christie RPMSP-D120U Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 51

background image

Section 4: Maintenance

4-2

RPMX-RPMSP-D120U & RPMSP-D275U Setup Guide

020-100038-02 Rev. 1 (09/08)

Operate the projector in an environment, which meets the operating range as
specified in

Section 6 – Specifications.

◊

Do not operate the projector close to water, such as near a swimming pool.
Do not operate in extremely humid environments.

◊

Do not place the projector on an unstable cart, stand or table. A projector and
cart combination should be used with care. Sudden stops, excessive force and
uneven surfaces may cause the projector and cart combination to overturn.

◊

Do not ceiling mount this projector.

The 2 100/120W UHP lamps for the RPMX/RPMSP-D120U and the 275W UHP
lamps for the RPMSP-D275U require replacement when they have reached their
end of life (approximately 10000 hours for RPMX/RPMSP-D120U models and
2250 hours for RPMSP-D275U models), if they have failed during operation, or
have a drastic change in brightness (typical of aging lamps). To effectively
maintain operation of the projector it is best to be aware of any changes that
occur in brightness and the number of hours each lamp is in use. Refer to

4.4.

Lamp Replacement

for more details on lamp replacement.

Follow all safety and warning precautions regarding lamp replacement and
handling.

WARNING

Wait approximately 5 minutes to allow the lamp to

cool before removing.

Do not stick hands into the lamp compartment

during lamp replacement.

The lamp is under great pressure when hot and may

explode causing physical injury and/or property

damage. Allow a lamp to cool before handling and/or

powering down and unplugging the projector.

Use only the lamps supplied by CHRISTIE, in the

Lamp

Replacement Kit

for these projectors.

Use only the attachments and/or accessories recommended by CHRISTIE. Use of
others may result in the risk of fire, shock or personal injury.

WARNING

Use only the AC power cord supplied. Do not attempt

operation if the AC supply is not within the specified

voltage and power range. See

Section 6.

◊

Do not set or rest items on the power cord. Place the projector in an area
where the projector cord cannot be abused or damaged by persons walking
on it or by objects rolling over it.

◊

Operate the projector at the specified voltage only. Do not overload power
outlets and extension cords as this can result in fire or shock hazards.

Projector Location

h

Lamps

h

Power

Cord

h

and

Attachments

HOT

«
...
40
41
42
43
44
...
»

Содержание RPMSP-D120U




















































Отзывы:

Нет отзывов

Похожие инструкции для RPMSP-D120U

GR 0021 HMI 1200

Бренд: Griven Страницы: 16

Video Xtreme VX-40d

Бренд: Runco Страницы: 102

Insta-DE Series

Бренд: Elite Screens Страницы: 4

Бренд: Optoma Страницы: 4

Бренд: AV Stumpfl Страницы: 10

Бренд: Optoma Страницы: 25

Бренд: BenQ Страницы: 60

PJD6230 - XGA DLP Projector

Бренд: ViewSonic Страницы: 2

DLA-G15U - D-ila Projector, 1500 Ansi Lumens

Бренд: JVC Страницы: 8

Бренд: JVC Страницы: 7

Бренд: JVC Страницы: 6

DLA-HD10KSU - 1080p Home Theater Projector

Бренд: JVC Страницы: 6

Бренд: JVC Страницы: 8

DLA-G150CL - D-ILA Projector - 100 ANSI Lumens

Бренд: JVC Страницы: 4

Бренд: JVC Страницы: 4

Бренд: JVC Страницы: 15

DLA-G150HT - Cineline Projector

Бренд: JVC Страницы: 40

Бренд: JVC Страницы: 50

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды