background image

Power mode

Functionality

• 100 - 130 VAC; 200 - 240 VAC

• Less brightness

To connect AC power to the projector:

1. Connect AC power to the appropriate AC inlet on the projector.
2. If using full power mode, to ensure AC power cord does not fall out, pull down the safety latch

and lock in place.
To unplug, press tab and pull up the latch to release.

Turning on the projector

When the projector AC power supply is plugged in, the power is on.

Warning! If not avoided, the following could result in death or serious injury.

SHOCK HAZARD! Do not attempt operation if the AC supply is not within the specified voltage
and current, as specified on the license label.

1. Plug the projector into AC power.

When plugged in, the projector automatically powers on to standby mode within 60 seconds.
The display panel functionality becomes available.

2. To turn the light source on using the projector keypad, press and hold the Power 

 button

until you hear a beep.
To turn on the light source using the remote, press and hold the ON button until you hear a
beep.

Related information

Power requirements (on page 53)

Projector LED status indicators

Identify the LED state colors and meaning.

LED

State

Description

Blue

Solid

Standby

Light source is off. Video electronics are off.
Projector status is OK.

Installation and setup

Mirage 304K (Bm.1) Installation and Setup Guide

23

020-102013-12 Rev. 1 (09-2022)

Copyright 

©

 2022 Christie Digital Systems USA, Inc. All rights reserved.

If printed, please recycle this document after use.

Содержание Mirage 304K





































































Отзывы: