Christie DLV 1280 Скачать руководство пользователя страница 73

Страница: 73 / 96

MAINTENANCE

DLV 1280 User's Manual

4-13

The display is faint...
1. Brightness and/or contrast may be set too low. Increase the brightness and/or

contrast settings.

2. The projection room may be too bright. Lower the intensity of projection

room lighting and reduce light reflections as much as possible.

3. The projector may be too far from the screen. Move the projector closer to

the screen.

4. The location of the audience with respect to the screen may not be adequate.

Make sure the audience is within the viewing angle set by the projector and
screen position, and the screen type.

5. The source may be double terminated. Ensure the source is terminated only

once.

6. The source (if non-video) may need sync tip clamping. Turn the “

Clamp Tip

”

option to “

” in the Horizontal Settings menu.

The display is reversed or upside down...
1. The projector's image orientation is not set correctly for the current

installation. Refer to 2.6, Operating Orientation, to set the projector's image
orientation to match your installation.

The upper portion of the display is waving, tearing or jittering...
1. This can sometimes occur when the source is a VCR or video signal. If you

are using a VCR, turn the "

VCR

" option to “

” within the Image Settings

menu.

Portions of the display are cut off or wrap to the opposite edge...
1. Horizontal/vertical size or position may need adjustment. Adjust until the

entire image is visible and centered.

The display appears compressed or stretched
1. The

Horizontal Size (or Vertical Size) setting may be incorrect for the

current source. Adjust H-Size in the Horizontal Settings menu (or adjust V-
Size in the Vertical Settings menu).

2. The frequency of the pixel sampling clock is incorrect for the current source.

Adjust pixel tracking up or down.

Display quality appears to drift from good to bad, bad to good...
1. The operating temperature of the projector may not be constant. Watch that

the projector is not located too close to heating/air conditioning vents.

2. The source input signal may be of low quality.

3. The horizontal or vertical frequency of the input may have changed at the

source end.

An unknown menu has appeared
1. You may have accidentally entered a special engineering code. Press

cancel the function and return to presentation level.

Symptom

CAUSE / REMEDY:

Symptom

CAUSE / REMEDY:

Symptom

CAUSE / REMEDY:

Symptom

CAUSE / REMEDY:

Symptom

CAUSE / REMEDY:

Symptom

CAUSE / REMEDY:

Symptom

CAUSE / REMEDY:

Содержание DLV 1280

































































































Результаты поиска

Содержание DLV 1280

Отзывы:

Похожие инструкции для DLV 1280

Бренды по названию

Популярные бренды

Christie DLV 1280, Руководство пользователя

Результаты поиска

Содержание DLV 1280

Отзывы:

Похожие инструкции для DLV 1280

Бренды по названию

Популярные бренды