Christie DLV 1280 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 96

background image

INSTALLATION & SETUP

2-22

DLV 1280 User's Manual

Step 5: Set the Jumpers
Set the jumpers as shown in Figure 2-30. Take care to refer to the correct part of
the drawing — IR or wired (optional). Use tweezers or needle-nose pliers to
remove and replace each jumper as necessary.

•

J1 jumper: For either remote, set between pins 1 and 2 to set as Protocol
"A". Set between pins 2 and 3 to set as Protocol "B".

•

J2 jumper: For either remote, set between pins 2 and 3 as shown; otherwise,
the projector will not respond correctly to keypad commands.

•

J3 jumper: For the IR remote, make sure that the jumper is set between pins
2 and 3 as shown. For the wired remote, make sure that the jumper is set
between pins 1 and 2 as shown.

•

J4 jumper: For the IR remote, make sure that the jumper is set between pins
1 and 2 as shown. For the wired remote, make sure that the jumper is set
between pins 2 and 3 as shown.

Step 6
Replace battery compartment cover. Plug into projector (wired keypad only) and
test.

NOTE: Although they are similar, a wired keypad cannot be converted into an
IR remote keypad, nor vice versa.

SHORTCUT METHOD FOR CHANGING PROTOCOL:
You can also issue software protocol settings through the keypad. These settings
override the hard-wired jumper settings and remain in effect until the keypad is
either unplugged or until a battery is removed. At that point, keypad protocol
will then revert back to the hard-wired jumper settings (see above). Note that the
projector will automatically detect this return to hard-wired settings and will still
respond. To set the keypad protocol through software:

Press

= Protocol "A"

Press

= Protocol "B"

NOTE: If you set a remote keypad to a new protocol and the projector stops
responding entirely, the projector may be set to a conflicting protocol. Use the
projector's built-in keypad to access the Preferences menu. Under the relevant
keypad option, select the protocol that matches the new protocol of the remote
keypad. The projector should now respond properly.

«
...
23
24
25
26
27
...
»

Содержание DLV 1280

































































































Отзывы:

Нет отзывов

Похожие инструкции для DLV 1280

Nighthawk SX10000D

Бренд: NEC Страницы: 10

MultiSync VT440

Бренд: NEC Страницы: 8

MT1056 - MultiSync XGA LCD Projector

Бренд: NEC Страницы: 2

Бренд: NEC Страницы: 17

Бренд: NEC Страницы: 9

NP110 - SVGA DLP Projector

Бренд: NEC Страницы: 2

Бренд: NEC Страницы: 6

NP110 - SVGA DLP Projector

Бренд: NEC Страницы: 6

LT75Z - MultiSync SVGA DLP Projector

Бренд: NEC Страницы: 2

Бренд: NEC Страницы: 6

Бренд: NEC Страницы: 106

Бренд: NEC Страницы: 107

Бренд: NEC Страницы: 6

Бренд: NEC Страницы: 4

Бренд: NEC Страницы: 14

Бренд: NEC Страницы: 255

Бренд: NEC Страницы: 4

Бренд: NEC Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды