Christie DLV 1280 Скачать руководство пользователя страница 17

Страница: 17 / 96

INSTALLATION & SETUP

2-14

DLV 1280 User's Manual

If you have an S-Video (SVHS) source, connect it to the projector’s rear input
panel at

VID 2.

Depending on the source, use either the two BNC connectors

labeled “

Y/Cr

and

C/Cb

” (luminance and chrominance) or use the 4-pin mini DIN

connector labeled “

SVID

”— do not use both types of connectors simultaneously.

See Figure 2-17.

Figure 2-17. Connecting an S-Video Source

VID 2 AUDIO:

To control audio levels in an audio/visual system, connect pre-

amplified (line level) audio inputs to the left and right audio inputs labeled

VID 2

If you want to connect an extra S-Video source, connect to

DAT 1

using the red

and blue BNC connectors (labeled “

” and “

”) and use

DAT 1 AUDIO

. Make

sure to connect the “Y” signal (luminance) to red, the “C” signal (chrominance)
to blue. See Figure 2-18.

Figure 2-18. Connecting an Extra S-Video Source

S-Video Input

Extra S-Video Input

Содержание DLV 1280

































































































Результаты поиска

Содержание DLV 1280

Отзывы:

Похожие инструкции для DLV 1280

Бренды по названию

Популярные бренды

Christie DLV 1280, Руководство пользователя

Результаты поиска

Содержание DLV 1280

Отзывы:

Похожие инструкции для DLV 1280

Бренды по названию

Популярные бренды