CHIEF 451321 Скачать руководство пользователя страница 25

Страница: 25 / 28

Troubleshooting (continued)

Problem

Possible Cause

Possible Solution

Rear lift will not raise

Lift switch off

Rotate switch to “LIFT”

Auxiliary line valve open

Close all auxiliary line valves

Too much weight at rear of machine

Move vehicle forward on deck

Mainframe control cord

Inspect mainframe control cord.

Inspect cord for damage. Contact Chief Collision

Technology for repair or replacement if necessary

Pump not building pressure

See pump troubleshooting

Contamination in control manifold rear lift

valve

Remove and inspect V2 valve. Contact Chief Collision

Technology for repair or replacement if necessary

Bad rear lift valve coil

Check for magnetic field at V2 coil. Contact Chief

Collision Technology for repair or replacement if

necessary

Front lift will not raise

Lift switch off

Rotate switch to “LIFT”

Auxiliary line valve open

Close auxiliary line valves

Tilt switch not operating

Inspect tilt for damage. Contact Chief Collision

Technology for repair or replacement if necessary

Machine overloaded in front

Move vehicle rearward on deck

Towers roll hard

Dirt on outer track

Clean outer track

Dirt in outer tower roller bearings

Clean outer tower roller bearings

Tower shimmed incorrectly

Re-shim tower. Contact Chief Collision Technology

service representative

Damaged inner roller

Replace inner roller. Contact Chief Collision

Technology service representative

Damaged track

Repair track. Contact Chief Collision Technology

service representative

Sure-Lock difficult to engage

Dirt on deck

Clean deck

Dirt in Sure-Lock pivots

Clean Sure-Lock pivots. Apply a few drops of oil to

pivot and operate Sure-Lock mechanism

Sure-Lock out of adjustment

Re-shim Sure-Lock. Contact Chief Collision

Technology service representative

Sure-Lock difficult to disengage

Dirt in Sure-Lock pivots

Clean Sure-Lock pivots. Apply a few drops of oil to

pivots and operate Sure-Lock mechanism

Sure-Lock out of adjustment

Re-shim Sure-Lock. Contact Chief Collision

Technology service representative

Collars jump under load

Improper fit between collar and tower pipe

Refit collar. Contact Chief Collision Technology

service representative

PHOENIX

USERS MANUAL

Содержание 451321




























Результаты поиска

Содержание 451321

Отзывы:

Похожие инструкции для 451321

Бренды по названию

Популярные бренды

CHIEF 451321, Руководство пользователя

Результаты поиска

Содержание 451321

Отзывы:

Похожие инструкции для 451321

Бренды по названию

Популярные бренды