Chevrolet Tavera Скачать руководство пользователя страница 50

Страница: 50 / 205

NOTE

WHEN REMOVING FROST AND FOG FROM THE FRONT AND SIDE

GLASSES

Turn the Air distribution mode knob to the "DEFROSTING" position.

When operating the air conditioner with the Air distribution mode knob set to the

"DEFROSTING" position, do not set the air conditioner to the "MAXIMUM

COOLING" position. Otherwise the outside of the glass could fog and cause poor

visibility ahead.

QUICK DEFROSTING MEASURE

Turn the temperature control knob clockwise until it stops. Turn the Air

distribution mode knob to the "DEFROSTING" position. Slide the Air

intake/circulation changeover lever to circulate air.

Continuous defrosting operation in the circulation status may cause fogged glass

and poor visibility. On completion of defrosting, be sure to change to the air intake

status.

NOTE

Содержание Tavera














































































































































































































Результаты поиска

Содержание Tavera

Отзывы:

Chevrolet Tavera, Руководство пользователя, Страница: 50 / 205

Результаты поиска

Содержание Tavera

Отзывы: