Cherry Aerospace G-689, Оригинальное руководство пользователя

Страница: 12 / 16

10
PULLING HEADS
Pulling heads are not furnished and must be ordered separately. Make certain the pulling head is kept clean, especially around
the riveting end, as adhesives, chips, sealants, etc., will clog up the serrations of the jaws and may cause slippage of the stem.
Please refer to the pulling head charts below for the proper selection.
TOOL CAPACITY CHART
The G689 Riveter is recommended primarily for 1/4" diameter CherryLOCK® rivets. However, using the H681 Series Pulling
Heads it can be used to install
all diameters and lengths of CherryLOCK rivets as indicated below.
STANDARD CHERRYLOCKS (NAS 1398 & 1399)
ALUMINUM MONEL ST. STEEL
CR2642
CR2163 CR2162 CR2562
CR2643 CR2652
CR2164 CR2563 CR2663 CR2662
CR2263
CR2262
CR2564
CR2663
CR2664
PULLING
HEAD
RIVET DIA.
UNIV.
HEAD
CTSK.
HEAD
UNIV.
HEAD
CTSK.
HEAD UNIV.
HEAD
CTSK.
HEAD
H681-3C -3 - - - - ALL ALL
H681-4C -4 ALL ALL ALL ALL ALL ALL
H681-5C -5 ALL ALL ALL ALL ALL ALL
H681-6C -6 ALL ALL ALL ALL ALL ALL
H681-8C
-8 ALL ALL ALL ALL ALL ALL
BULBED CHERRYLOCKS (NAS 1738 & 1739)
ALUMINUM MONEL INCONEL
CR2235
CR2239
CR2238 CR2539 CR2538 CR2839 CR2838
CR2245
CR2249
CR2248 CR2545 CR2540 CR2845 CR2840
PULLING
HEAD
RIVET DIA.
UNIV.
HEAD
CTSK.
HEAD UNIV.
HEAD
CTSK.
HEAD
UNIV.
HEAD
CTSK.
HEAD
H681-4C -4 ALL ALL ALL ALL ALL ALL
H681-5C
-5 ALL ALL ALL ALL ALL ALL
H681-6C -6 ALL ALL ALL ALL ALL ALL
OTHER PULLING HEADS THAT WILL FIT THIS TOOL ARE SHOWN ON THE CHART BELOW
PULLING HEAD TYPE ADAPTER RIVET
RIVET
DIAMETERS
MAXIMUM
GRIP
H9015 Straight 680B46 MS 3/32, 1/8, 5/32, 3/16 ALL
H9055 Straight 680B46 CherryLOCK “A”, MS 3/32, 1/8, 5/32, 3/16 ALL
H9040 Straight 680B57 MS 1/8, 5/32, 3/16, 1/4 ALL
H781-456 Rt. Angle 680B205 CherryMAX
®
1/8, 5/32, 3/16 ALL
H753A-456 Rt. Angle 680B205 CherryMAX 1/8, 5/32, 3/16 ALL
H827-8 Offset 680B210 CherryMAX 1/4 ALL
H828-8 Rt. Angle 680B210 CherryMAX 1/4 ALL
H828-5MB/H828-6MB Rt. Angle 680B210 Maxibolt 5/32, 3/16 ALL
H680B200A Straight - CherryMAX 1/8, 5/32, 3/16 ALL
H680B208 Straight - CherryMAX 1/4 ALL
INSTALLING H681 SERIES PULLING HEADS ON RIVETER
1. Remove knurled cap (A) from front of riveter head.
2. Place jaw assembly (D) inside collet (C).
3. Insert spring end of jaw assembly into hole in head piston (14). Apply enough pressure to engage collet threads. Turn until
collet (C) bottoms on shoulder of head piston and collet lock snaps into slot in head piston. Hand tighten. NOTE: To remove
collet, push collet lock back into collet using a blunt tool while turning collet counterclockwise.
4. Place sleeve assembly (B) over collet and head piston. Slip knurled cap (A) over the sleeve assembly and hand tighten onto
end of riveter head. Extensions for the H681 pulling heads can be ordered in lengths of 2", 6", 12" and 24".