background image

 
Page 10 of 17 

Intimidator Scan LED 300 User Manual (Rev. 3) 

Operation 

 

 

DMX Operation 

 

 

 

This is the operating mode which will allow for control with an external DMX controller. You must 
set the starting address for this mode. If this is your first time using DMX, then it is recommended 
that you refer to the “DMX Primer” section in the “Appendix” of this manual. 
 

1. 

Press 

<MODE/ESC>

 until 

d

(

001~512

) appears on the LED screen. 

2. 

Using 

<UP>

 and 

<DOWN>

, select the starting address 

d

(

001~512

). 

3. 

Press 

<MODE/ESC> 

until one of the DMX personalities appears on the LED screen  

(

8CH, 11CH)

. The most recent DMX personality selected will appear. 

4. 

Use 

<UP>

 and 

<DOWN>

 to change the personality. 

5. 

Press 

<ENTER>

.

 

 

 

 

Only connect 32 fixtures to a single DMX daisy chain! 

 

 

Master/Slave Mode (Sound-Active, Auto Mode) 

 

 

 

This mode allows a single unit, the master, to operate in one of the standalone modes, while one 

or more fixtures, slaves, synchronize their responses to the master. 

Master: 

The master fixture may be set in any of the STANDALONE modes: sound-active, fast, or 
slow. 

Slave: 

1. 

Press 

<MODE/ESC>

 until 

NASL

 appears on the LED screen.

 

2. 

Using 

<UP>

 and 

<DOWN>

 select 

<SLAu>

.

 

3. 

Press 

< ENTER >

.

 

<Son>

 will appear on the screen.

 

 

 

 

Only connect 31 slave fixtures when operating in this mode! 

 

 

Automatic-Slow 

 

 

 

This fixture has a preprogrammed chase that will operate in a preprogrammed, slow playback 
speed. 
 
Access this mode via the control panel on the front of the fixture. Please see the instructions 
below for further explanation. 
 

1. 

Press 

<MODE/ESC>

 until one of the standalone modes appears on the LED screen 

(

SLAv, NStS, NAFA, NASL

). 

2. 

Using 

<UP>

 and 

<DOWN>

, select 

NASL

3. 

Press 

<ENTER>

<SLoU>

 will appear. 

 

 

Automatic-Fast 

 

 

 

This fixture has a preprogrammed chase that will operate in a preprogrammed, fast playback 
speed. 
 
Access this mode via the control panel on the front of the fixture. Please see the instructions 
below for further explanation. 
 

1. 

Press 

<MODE/ESC>

 until one of the standalone modes appears on the LED screen 

(

SLAv, NStS, NAFA, NASL

). 

2. 

Using 

<UP>

 and 

<DOWN>

, select 

NAFA

3. 

Press 

<ENTER>

<FASt>

 will appear on the screen. 

 

 

 

 

Содержание Intimidator Barrel LED 300


















Отзывы: