manualshive.com logo in svg

Chatsworth Products 60106-001, Руководство пользователя

Поделиться
Скачать
Chatsworth Products 60106-001 Скачать руководство пользователя страница 19

RIM-Protocol Converter User Guide - Version 1.0

Chatsworth Products, Inc. (CPI) • 800-834-4969

19

C H A P T E R

3

CONFIGURATION

The Protocol Converter allows you to view and configure slave devices and slave registers over the Web. To access the 
Web interface, you must first set up the Protocol Converter to communicate over the Internet. To set the IP address, see 
“Configure Communications” on page 19.

Follow the order of the sections in this chapter to completely configure the slave devices, registers, and the Protocol Converter.

3.1. 

Configure Communications

The Protocol Converter will not communicate over a user’s network the first time it is
connected to the network. At the factory, the Protocol Converter is set with a default IP
address of 10.0.0.188 and Subnet Mask: 255.255.255.0.

You must change this default address to an IP address that corresponds with your network
before the Protocol Converter can communicate over the network. Use one of these vehicles to
change the IP address:

¥ 

Web browser

¥ 

The EIA-232 interface

Содержание 60106-001





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды