Charmhigh CHM-T48VB страница 34 Скачать руководство пользователя | Manualshive

Страница: 34 / 54

background image

Charmhigh-V1.0-2016 |

34

All Rights Reserved

11.2. Vacuum Detection Set

Screen as show below.

Figure.

11-6

(1)

Nozzle 1\2-suck:

Switch nozzle in blow;

(2)

Nozzle 1\2-blow:

Switch nozzle in blow;

(3)

Air pressure status list:

Note, ordinary pressure and vacuum value in list are

valid only after sucking material at least one time when running, or it will display

invariable 0; ordinary pressure is the pressure detected before sucking material;

vacuum value is the absolute value of that pressure after sucking minus ordinary

pressure, bigger value indicates better effect, effect is judged by partition the

range of this value;

(4)

MHead 1\2 threshold 1:

I.e. lower limit of vacuum value, no material is

determined if vacuum value is below this value when running, and machine will

retry, otherwise indicates material is sucked;

(5)

Nozzle 1\2 threshold 2:

I.e. upper limit of vacuum value, bad material is

determined if vacuum value is below this value when running, and material will be

thrown away, otherwise indicates good suction and material will be mounted;

Note, threshold 1 must smaller than threshold 2, threshold 2 must smaller than

detected vacuum value when suction OK, threshold 1 must greater than detected

vacuum value when no material. Recommended values: threshold 1 must less than

detected vacuum value when suck empty material; threshold 1 less 0.2 than threshold 2,

«
...
32
33
34
35
36
...
»

Содержание CHM-T48VB























































Отзывы:

Нет отзывов

Похожие инструкции для CHM-T48VB

Бренд: UnionSpecial Страницы: 56

Бренд: GE Страницы: 698

Бренд: SAMCHULLY Страницы: 48

Бренд: T&D Страницы: 28

Бренд: Tar River Страницы: 26

Бренд: ZOLL Страницы: 38

Бренд: ZOLL Страницы: 36

Nature2 Fusion soft

Бренд: Zodiac Pool Systems Страницы: 52

Бренд: Oliver Страницы: 38

Бренд: Wacker Neuson Страницы: 34

Бренд: Tripp Lite Страницы: 24

Бренд: TDX Tech Страницы: 27

EPL-HB-150LED-RT-IBSC

Бренд: Larson Electronics Страницы: 2

ARCHISHAPE 2.0 Linear

Бренд: Osram Страницы: 7

Fusionchef pearl

Бренд: Julabo Страницы: 43

Бренд: GYM form Страницы: 40

Бренд: T&R Страницы: 26

Бренд: Lightolier Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды