Char-Broil 15601898, Руководство по эксплуатации

Страница: 3 / 68

3 GB
CAUTION
• Read and follow all safety statements, assembly
instructions and use and care directions before
attempting to assemble and cook.
• Some parts may contain sharp edges.
Wearing protective gloves is recommended.
Safety Tips
When appliance is not in use, turn off all control
knobs and gas.
Use long-handled barbecue utensils and oven
mitts to avoid burns and splatters. Use protective
gloves when handling hot components.
The grease tray must be inserted into appliance
and emptied after each use. Do not remove
grease tray until appliance has completely
cooled.
If you notice grease or other hot material dripping from
appliance onto valve, hose or regulator, turn off gas
supply at once. Determine the cause, correct it, then
clean and inspect valve, hose, and regulator before
continuing. Perform a leak test.
Change the gas container outside and away from
people. DO NOT disconnect or change gas
container within 3m of an open flame or other
ignition source or other people.
•Putting out grease fires by closing the lid is not
possible. Grills are well ventilated for safety
reasons.
•Do not use water on a grease fire, Personal
injury may result. If a persistent grease fire
develops turn knobs off.
•If appliance has not been regularly cleaned, a
grease fire can occur that may damage the
product. Pay close attention while preheating
or burning off food residue to insure that a
grease fire does not develop. Follow
instructions on General appliance Cleaning
and Cleaning The Burner Assembly to prevent
grease fires.
•
The best way to prevent grease fires is
regular cleaning of the appliance.
Grease Fires
Be very careful when you open the lid, since hot
steam may escape.
Be very careful when children, the elderly or pets
are nearby.
This appliance shall only be used with PRIMUS
Powergas model 2202 (450 g) butane-propane gas
mixture cartridge. This appliance shall only be used
with EN 417 butane-propane mixture cartridge.
It may be hazardous to attempt to fit other types of
gas cartridges.
Check that seals are in place and in good condition
before connecting to the gas container. Check the
seals before connecting a new gas container to the
appliance.
Do not use the appliance if it has damaged or worn
seals. Do not attempt to repair seals. Obtain new
parts form the manufacturer.
Do not use an appliance which is leaking, damaged
or which does not operate properly.
If there is a leak on your appliance (Smell of gas),
take it outside immediately into a well ventilated
flame free location where the leak may be detected
and stopped. If you wish to check for leaks on your
appliance, do it outside. Do not try to detect leaks
using a flame, use soapy water.
GAS CARTRIDGES
•
•
•
•
•
•
•
REGULATOR REQUIREMENTS
Only use regulator supplied with this product or a
replacement supplied by the manufacturer.
•
Check that gas cartridge is empty before changing it
(shake to hear the noise made by the liquid). •
Check that burners are extingushed before
disconnecting the gas cartridge. •
•
•
•
•
•
•
Rotate Match
Light Hole
Cover
View is from
rear of
appliance
A
Match Light
Hole
Ignitor Lighting
READ INSTRUCTIONS BEFORE LIGHTING.
Do NOT lean over appliance while lighting.
1.
Turn OFF gas burner control valve.
2. Connect LP gas cylinder.
3. Open the grill lid.
4. Press and turn the control knob to the position.
5 . Push and hold ELECTRONIC IGNITOR button until the burner
lights.
6. Once ignited, turn the control knob to the desired setting.
7. If ignition does not occur in 5 seconds, turn the burner control
knob OFF , wait 5 minutes, and repeat lighting procedure.
If ignition still does not occur, follow match-lighting
instructions.
Match-Lighting
Do NOT lean over appliance while lighting.
1. Turn OFF gas burner control valve.
2. Open grill lid.
3. Connect LP gas cylinder
4. Insert match into match holder. Strike match. Place lit match
into match light hole at the rear of the grill bottom, shown “ A ”.
Make sure lit match is placed inside through the hole and near
burner.
5. Push in and turn control knob to position . Be sure burner
lights and stays lit.
6. If ignition does not occur in 5 seconds, turn the burner control
knob OFF , wait 5 minutes, and repeat lighting procedure.