background image

22

Install the Door Control

1.5

Position the bottom hole of the door

control over the screw and slide
down into place.

1.6

Lift the push bar up and mark the top hole.

1.7

Remove the door control from the wall

and drill a 5/32 inch (4 mm) hole for
the top screw.

1.8

Position the bottom hole of the

door control over the screw and
slide down into place. Attach the
top screw.

DRYWALL

6ABx1-1/2"

Drywall Anchor

6-32x1"

GANG BOX

2

Wire the door control to the garage door opener

HARDWARE

Insulated Staple

PRE-WIRED INSTALLATIONS:

When wiring

the door control to the garage door opener

make sure you use the same wires that are
connected to the door control.

2.1

Run the white and red/white wire from the door control to

the garage door opener. Attach the wire to the wall and
ceiling with the staple (not applicable for gang box or pre-
wired installations). Do not pierce the wire with the staple
as this may cause a short or an open circuit.

Staple

2.2

Strip 7/16 inch (11 mm) of insulation

from the end of the wire near the
garage door opener.

7/16" 
(11 mm)

2.3

Connect the wire to the red and

white terminals on the garage
door opener. To insert or
release wires from the terminal,
push in the tab with screwdriver
tip.

RED WHITE

WHITE

GREY

Содержание WD962KEV

















































Отзывы: