1
ASSURELINK
TM
GARAGE DOOR OPENER
SMARTPHONE CONTROL KIT
MODEL 139.53999
To prevent possible SERIOUS INJURY or DEATH from electrocution:
• Be sure power is NOT connected BEFORE installing door control.
• Connect ONLY to 7-28 VOLT low voltage wires.
To prevent possible SERIOUS INJURY or DEATH from a closing
garage door:
• Install door control within sight of garage door, out of reach of
children at a minimum height of 5 feet (1.5 m), and away from ALL
moving parts of door.
• NEVER permit children to operate or play with door control push
buttons or remote control transmitters.
• Activate door ONLY when it can be seen clearly, is properly
adjusted, and there are no obstructions to door travel.
• ALWAYS keep garage door in sight until completely closed. NEVER
permit anyone to cross path of closing garage door.
• DO NOT install this door control on garage door opener systems
controlling one-piece or swing doors.
To provide an adequate visual alert, the garage door opener light
bulb(s) MUST be a minimum of 40 Watt (or equivalent).
This kit includes the Assurelink™ Control Panel model 41a7928-1 and the
Assurelink™ Internet Gateway model 41A7665. The control panel is
intended to be installed with Craftsman
®
Security
✚
™ Garage Door
Openers manufactured between 1998 and present. The Assurelink™
Control Panel is NOT compatible with Security
✚
2.0™ Garage Door
Openers. DO NOT install this door control on garage door opener
systems controlling one-piece or swing doors.
APPLICATION
The Assurelink™ Control Panel offers a quick and convenient way to add
Assurelink™ technology to your existing garage door opener. Assurelink™
technology uses a 900MHz signal to provide two-way communication
between the garage door opener and Assurelink™ enabled accessories.
When programmed to the Assurelink™ Internet Gateway you can monitor
and control your garage door from any internet enabled computer or
smartphone. You may program up to 12 Assurelink™ remote controls, 2
Assurelink™ keyless entries and a combination of 16 Assurelink™
accessories to the Assurelink™ control panel. For full compatibility, see
page 4.
OVERVIEW
Install the control panel in place of the existing door control. Due to
power consumption the control panel cannot be used in conjunction with
another wired door control connected to your garage door opener. If an
additional door control is needed, the
wireless door control model
41A7773-1
can be programmed to the control panel. To program the
41A7773-1 to the control panel, follow the remote control programming
steps. When in battery back-up mode, any feature using unattended
operation such as Timer-to-Close, closure from a garage door and gate
monitor or remote operation utilizing the Assurelink™ Internet Gateway
will be disabled.
1. Disconnect all electrical and battery power (if applicable) to the
garage door opener.
2. Remove the existing door control from the wall.
3. Note the polarity of the wires connected to the existing door
control.
• Label the wire connected to the RED terminal.
• Label the wire connected to the WHITE terminal.
Disconnect the wires from the existing door control.
4. Connect the wires to the new control panel. Make sure the polarity
is correct.
• Red wire to the R terminal.
• White wire to the W terminal.
5. Mount the control panel to the wall.
6. Reconnect power. The yellow command LED and the red learn LED
will blink quickly for up to 5 minutes as the control panel
recharges. When the control panel is operational, the yellow
command LED will glow steadily.
7. To test the control panel, press the push bar to activate the garage
door opener.
INSTALL THE ASSURELINK™ CONTROL PANEL
Existing Door Control
Discard, donate
or recycle
Wire from
RED terminal
Connect
RED wire to
R
terminal
Wire from
WHITE
terminal
Connect
WHITE
wire to
W
terminal
Assurelink™ Control Panel
•
If the yellow command LED does not turn on, reverse the wires
connected to the R and W terminals of the control panel. Replace
wire if necessary.
•
If yellow and red LEDs are blinking slowly, the control panel is not
compatible with your garage door opener.
•
If the yellow and red LEDs are blinking quickly, the control panel is
charging, and may take up to 5 minutes to become operational.
TROUBLESHOOTING
