Chamberlain WD962KEV Скачать руководство пользователя страница 35

35

Your garage door opener is equipped with features to provide you with greater control over your
garage door operation.

Alert2Close

The Alert2Close feature provides a visual and an audible alert that an unattended door is closing.

Timer-to-Close

The Timer-to-Close feature automatically closes the door after a specified time period that can be
adjusted using the door control. Prior to the door closing there will be an audible and visual alert.

MyQ™

MyQ™ technology uses a 900MHz signal to provide two-way communication between the garage door
opener and MyQ™ enabled accessories. Your garage door opener is compatible with up to 8 MyQ™
accessories.

REMOTE CONTROLS AND DOOR CONTROLS (MyQ™)

Your garage door opener has already been programmed at the factory to operate with your remote
control, which changes with each use, randomly accessing over 100 billion new codes. Compatible with
MyQ™ enabled accessories, see page 47.

NOTE:

Older Chamberlain remote controls, door controls, and third party products are not compatible.

MyQ

TM

Accessories

MEMORY CAPACITY

Remote Controls

Up to 8

Door Controls

Up to 2 MyQ™ door controls

Keyless Entries

Up to 1

THE PROTECTOR SYSTEM

®

(SAFETY REVERSING SENSORS)

When properly connected and aligned, the safety reversing sensors will detect an obstruction in the
path of the infrared beam. If an obstruction breaks the infrared beam while the door is closing, the door
will stop and reverse to full open position, and the opener lights will flash 10 times. If the door is fully
open, and the safety reversing sensors are not installed, or are misaligned, the door will not close from
a remote control. However, you can close the door if you hold the button on the door control or keyless
entry until the door is fully closed. The safety reversing sensors do not effect the opening cycle.

ENERGY CONSERVATION

For energy efficiency the garage door opener will enter sleep mode when the door is fully closed. The
sleep mode shuts the garage door opener down until activated. The sleep mode is sequenced with the
garage door opener light bulb; as the light bulb turns off the sensor LEDs will turn off and whenever the
garage door opener lights turn on the sensor LEDs will light. The garage door opener will not go into
the sleep mode until the garage door opener has completed 5 cycles upon power up.

LIGHTS

The garage door opener light bulbs will turn on when the opener is initially plugged in; power is
restored after interruption, or when the garage door opener is activated. The lights will turn off
automatically after 4-1/2 minutes. An incandescent A19 light bulb (100 watt maximum) or for maximum
energy efficiency a 26W (100W equivalent) compact fluorescent light (CFL) bulb may be used.

Light Feature

The garage door opener is equipped with an added feature; the lights will turn on when someone
enters through the open garage door and the safety reversing sensor infrared beam is broken. For
added control over the light bulbs on your garage door opener, see page 37.

USING YOUR GARAGE DOOR OPENER

The garage door opener can be activated through a wall-mounted door control, remote control,
wireless keyless entry or MyQ™ accessory.
When the door is closed and the garage door opener is activated the door will open. If the door senses
an obstruction or is interrupted while opening the door will stop. When the door is in any position other
than closed and the garage door opener is activated the door will close. If the garage door opener
senses an obstruction while closing, the door will reverse. If the obstruction interrupts the sensor beam
the garage door opener lights will blink 10 times. However, you can close the door if you hold the button
on the door control or keyless entry until the door is fully closed. The safety reversing sensors do not
affect the opening cycle.
The safety reversing sensor must be connected and aligned correctly before the garage door opener
will move in the down direction.

BATTERY BACKUP

The battery backup system allows access in and out of your garage, even when the power is out. When
the garage door opener is operating on battery power, the garage door opener will run slower, the light
will not function, the Battery Status LED will glow solid orange, and a beep will sound approximately
every 2 seconds.

Features

Содержание WD962KEV

















































Отзывы: