Chamberlain DDO8900W Скачать руководство пользователя

Страница: 1 / 32

For Light Duty Commercial Use

Install On High-Lift and Vertical

Sectional Doors With

Torsion Assemblies Only

NOT FOR RESIDENTIAL USE

Light-Duty Dock Door Operator

for Sectional Doors

Model DDO8900W

LiftMaster

300 Windsor Drive

Oak Brook, IL 60523

• Please read this manual and the enclosed safety materials carefully!
• The door WILL NOT CLOSE unless the Protector System

and cable tension monitor

are connected and properly aligned.

•  Periodic checks of the operator are required to ensure safe operation.
•  The model number is located on the front cover of the operator.
•  DO NOT exceed 10 complete cycles of door operation per hour.

This product is to be installed and serviced by a trained door systems technician only.

This product may require adjustments to door springs and/or track configurations. This

product is not intended for use on low headroom tracks with outside pickup drum or

doors utilizing extension springs.

2 YEAR WARRANTY

After Installation, Please Leave with Customer

Register your door operator to receive updates and offers from LiftMaster

Take a photo

of the

camera icon including

the points ( ).

Send it in

by texting

the photo to 71403

(US)

or visit

www.liftmaster.photo

(Global)

Содержание DDO8900W
































Результаты поиска

Содержание DDO8900W

Отзывы:

Похожие инструкции для DDO8900W

Бренды по названию

Популярные бренды

Chamberlain DDO8900W, Руководство пользователя

Результаты поиска

Содержание DDO8900W

Отзывы:

Похожие инструкции для DDO8900W

Бренды по названию

Популярные бренды