Chamberlain B550 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 48

background image

18

Installation

STEP 8 Install the door bracket (continued)

OPTION B - ONE-PIECE DOORS

1.

Center the door bracket on the top of the door, in line with the header bracket as shown.

2.

Mark either the left and right, or the top and bottom holes.

Metal Doors:

l

Drill 3/16" pilot holes and fasten the bracket with the self-threading screws provided.

Wood Doors:

l

Drill 5/16" holes and use 5/16"-18x2" carriage bolts, lock washers and nuts (not provided) or 5/16"x1-1/2"
lag screws (not provided) depending on your installation needs.

NOTE:

The door bracket may be installed on the top edge of the door if required for your installation. (Refer to the

dotted line optional placement drawing.)

HARDWARE

Self-Threading Screw
1/4"-14x5/8"

For a door with no exposed
framing, or for the optional
installation, use lag screws
5/16"x1-1/2" (not provided)
to fasten the door bracket.

Vertical
Centerline
of Garage
Door

Optional
Placement
of Door
Bracket

Door Bracket

Header Bracket

Header Wall

2x4 Support

(Finished Ceiling)

Door
Bracket

Top of Door
(Inside Garage)

Top Edge of
Door

Optional
Placement

Optional
Placement

Top Edge
of Door

Top of Door
(Inside Garage)

Door
Bracket

Hardware
(not provided)

Hardware
(not provided)

Metal Door

Wood Door

Self-Threading Screw

«
...
16
17
18
19
20
...
»

Содержание B550

















































Отзывы:

Нет отзывов

Похожие инструкции для B550

Бренд: Wallace Perimeter Security Страницы: 182

Бренд: Hamilton Beach Страницы: 9

Safety Signal 3800RGD

Бренд: Raynor Страницы: 36

Бренд: Avidsen Страницы: 8

Бренд: Richmond Страницы: 29

Бренд: Roma Страницы: 40

Бренд: Jaytech Страницы: 19

Бренд: tau Страницы: 12

Бренд: V2 Страницы: 104

Бренд: Automatic Technology Страницы: 56

Бренд: Rollerdor Страницы: 20

Бренд: Wallace Perimeter Security Страницы: 142

Бренд: CAME Страницы: 12

Quiet-Drive 425-1656

Бренд: Xtreme Garage Страницы: 28

Бренд: GATEXPERT Страницы: 54

Бренд: Raynor Страницы: 12

Whisper Drive Security+ 182671

Бренд: Chamberlain Страницы: 80

Бренд: Kenner Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды