Chamberlain B550 Скачать руководство пользователя страница 43

Страница: 43 / 48

Accessories

Remote Control:

Works with ALL Chamberlain

openers from 1993-present.

MyQ

compatible. Includes

visor clip.

Multi-Function Control Panel:

S 2.0

and Wi-Fi

compatible.

Motion Detecting Control

Panel:

Multi-function door control

with motion sensor that

automatically turns opener

lights on when it detects a

person entering the garage.

S 2.0

and Wi-Fi

compatible.

CLLP1

Laser Parking Assistant:

Park in the right spot every

time! A laser beam is activated

by your garage door opener

and projected on to the

dashboard of your vehicle to

guide perfect parking.

G956EV

Keychain Remote Control:

Works with ALL Chamberlain

openers from 1993-present.

MyQ

compatible. With key

ring.

G940EV

Wireless Keypad:

For use outside of the home

to enable access to the garage

using a 4-digit PIN. Works

with ALL Chamberlain openers

from 1993-present. MyQ

compatible.

Extension Brackets:

(Optional) For safety

reversing sensor installation

onto the wall or floor.

LOCK

LIGHT

LOCK

LIGHT

CLOSED

OPEN

041A5281-1

G8810CB

10 Foot (3 m) Rail

Extension:

To allow a 10 foot (3 m)

door to open fully.

8 Foot (2.4 m) Rail

Extension:

To allow an 8 foot (2.4 m)

door to open fully.

G8808CB

MyQ

Accessories

PILCEV

MyQ

Remote Lamp Control:

Monitor and control this plug

in lamp switch with the MyQ

Smartphone App.

041A7665 MyQ

Internet Gateway:

Offers longer range wireless

signal than standard Wi-Fi.

Plugs into your home router

as an optional way to provide

MyQ

Smartphone Control for

your garage door opener and

MyQ

light controls.

G953EV

041A7185-1

041A7327-1

WSLCEV

MyQ

Interior/Exterior Light

Switch

Monitor and control this wall

light switch with the MyQ

Smartphone App.

Содержание B550

















































Результаты поиска

Содержание B550

Отзывы:

Похожие инструкции для B550

Бренды по названию

Популярные бренды

Chamberlain B550, Руководство пользователя

Результаты поиска

Содержание B550

Отзывы:

Похожие инструкции для B550

Бренды по названию

Популярные бренды