Chamberlain B550 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 48

background image

38

Operation

TIMER-TO-CLOSE (DO NOT enable on one-piece doors)

The Timer-to-Close feature is not available on all door controls. Below is a list of door controls with the Timer-to-
Close feature:

041A7305-1 Smart Control Panel and 041A7327-1 Motion Detecting Control Panel

The Timer-to-Close feature automatically closes the garage door after a specified time period.

DO NOT enable TTC

if operating a one-piece door. TTC is to be used ONLY with sectional doors.

Factory default is set to off. The

garage door opener will beep and the lights will flash before closing the door. The TTC feature will deactivate if the
garage door encounters an obstruction twice; or the safety reversing sensors are incorrectly installed. The garage
door will reverse open and WILL NOT close until the obstructions are clear or the safety reversing sensors are
correctly installed. When the obstruction has been cleared or the safety reversing sensors have been aligned, the door
will close when the garage door opener is activated. TTC WILL NOT work if the garage door opener is operating by
battery power or if the safety reversing sensors are misaligned. This feature is NOT intended to be the primary
method of closing the door.

A keyless entry should be installed in the event of an accidental lock out when

using this feature.

Remote

Control

and

Keyless

Entry

Pre-programmed

remote

control

s

(2)

included,

no

need

to

program

the

remote.

To

add

or

reprogram

a

remote

control,

follow

the

instructions

below.

Older

Chamberlain

remote

controls

are

NOT

compatible,

see

page

43

for

compatible

accessories.

PROGRAM

USING

THE

DOOR

CONTROL

1.

Press the LEARN button on the door control to enter Programming Mode.

2.

Press the LEARN button again, the LED will flash once.

3.

Remote Control:

Press the button on the remote control that you wish to operate your garage door.

Keyless Entry:

Enter a 4-digit personal identification number (PIN) of your choice on the keyless entry

keypad. Then press the ENTER button.

The garage door opener lights will flash (or two clicks will be heard) when the code has been programmed.

The command LED will flash once.

or

The command LED will flash once again.

1

2

OR

PIN

?

?

?

?

3

or

To watch a video, go to

tinyurl.com/lcsf6xt

HomeLink

®

If your vehicle is equipped with HomeLink, a Compatibility Bridge

TM

(not included) may be necessary for certain

vehicles. Visit bridge.chamberlain.com to find out if a Bridge is needed.

«
...
36
37
38
39
40
...
»

Содержание B550

















































Отзывы:

Нет отзывов

Похожие инструкции для B550

Бренд: Nice Страницы: 8

Бренд: Novoferm Страницы: 46

Бренд: KitchenAid Страницы: 6

Бренд: Genie Страницы: 32

PowerLift Elite CS45EVO

Бренд: Chamberlain Страницы: 20

Бренд: beamUP Страницы: 26

Бренд: Hard Head Страницы: 33

Easy Parking Basic

Бренд: Baintex Страницы: 2

Бренд: CAME Страницы: 84

Бренд: CAME Страницы: 128

Бренд: HYDOM Страницы: 16

Bettis GVO-HP-FS Linear

Бренд: Emerson Страницы: 48

Бренд: Wayne-Dalton Страницы: 23

Бренд: Clopay Страницы: 29

Calypso 400-120V

Бренд: V2 Страницы: 11

Бренд: ZEC Automation Страницы: 23

Бренд: Westfalia Страницы: 30

Бренд: SmartPower Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды