Chamberlain B550 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 48

background image

42

DIAGNOSTIC CODE

SYMPTOM

SOLUTION

Up Arrow
Flash(es)

Down Arrow

Flash(es)

4

5

Opener runs approximately 6-8" (15-20 cm), stops and reverses.

Communication error to travel module. Check travel module connections, replace travel module if necessary.

4

6

The garage door opener will not close and the light bulbs flash.

Safety reversing sensors are misaligned or were momentarily obstructed. Realign both sensors to ensure both
LEDs are steady and not flickering. Make sure nothing is hanging or mounted on the door that would interrupt the
sensor’s path while closing.

The garage door opener can beep for several reasons:

l

Garage door opener has been activated through a device or feature such as Timer-to-Close or garage door
monitor, see page 35.

My remote control will not activate the garage door:

l

Verify the lock feature is not activated on the door control.

l

Reprogram the remote control.

l

If the remote control will still not activate the door check the diagnostic codes to ensure the garage door opener
is working properly.

My door will not close and the light bulbs blink on my motor unit:

The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the
down direction.

l

Verify the safety reversing sensors are properly installed, aligned and free of any obstructions.

My garage door opener light(s) will not turn off when the door is open:

The garage door opener is equipped with a feature that turns the light on when the safety reversing sensors have been
obstructed or when the motion sensor on the door control detects movement in the garage. These features can be
disabled using the door control, see page 35.

My neighbor’s remote control opens my garage door:

Erase the memory from your garage door opener and reprogram the remote control(s).

The LEDs on the door control blink:

If you have a Smart Control Panel installed and the TTC is set to a custom time, press the ON button on the Premium
Motion-Detecting Control Panel to set the time properly.

My vehicle's Homelink

®

is not programming to my garage door opener:

Compatibility Bridge

TM

(not included) may be necessary for certain vehicles. Visit bridge.chamberlain.com to find out

if a Bridge is needed.

Wi-Fi troubleshooting

The garage door opener will NOT enter Wi-Fi LEARN mode:

l

After the initial installation of the garage door opener, the garage door opener must complete a full cycle (open
and closed) before the Wi-Fi LEARN mode can be activated.

l

If there has been a recent power outage, the garage door opener must complete a full cycle before the Wi-Fi
LEARN mode can be activated.

See page 32 to activate Wi-Fi LEARN mode.

If your black adjustment button is not solid green go to wifihelp.chamberlain.com.

Troubleshooting

«
...
40
41
42
43
44
...
»

Содержание B550

















































Отзывы:

Нет отзывов

Похожие инструкции для B550

Бренд: FAAC Страницы: 35

Бренд: FAAC Страницы: 24

Бренд: RAMSET Страницы: 28

Бренд: Byan Страницы: 29

Бренд: CAME Страницы: 24

Cardin SLX Series

Бренд: Riello Elettronica Страницы: 36

Бренд: GDS Страницы: 9

GDS 550P Series

Бренд: GDS Страницы: 15

Бренд: GDS Страницы: 17

Бренд: GDS Страницы: 17

Gold400A Series

Бренд: V2 Страницы: 76

Smart Roller Nano

Бренд: Smart Openers Страницы: 16

Бренд: quiko Страницы: 8

Rotello QK-R300

Бренд: quiko Страницы: 18

SPIDER QK-S400BKIT

Бренд: quiko Страницы: 22

SCARABEO QK-SCA230

Бренд: quiko Страницы: 24

Бренд: quiko Страницы: 24

Бренд: Janus Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды