CETAC Aridus II Скачать руководство пользователя страница 36

Страница: 36 / 62

Aridus II™ Operator’s Manual

Disconnect the NEBULIZER SUPPLY line from the quick-connect fitting on the

back of the Aridus II

™

as in (4).

Disconnect the SAMPLE OUT Teflon

-lined PVC tubing from the ¼ inch

threaded fitting on the back of the Aridus II

™

If in use, power off and disconnect the ASX–112FR autosampler. Remove the

ASX-112FR from the top of the Aridus II

™

Remove all screws from the lid of the Aridus II

™

. There are a total of 12 screws

(four top, four left-side, four right-side).

Carefully remove the lid of the Aridus II

™

by lifting the lid straight up and off.

The membrane desolvator is a modular assembly located in the rear half of the

Aridus II

™

. See Figure 6-4. The membrane desolvator may be completely

removed from the Aridus II

™

and conveniently cleaned on a work bench.

Figure 6-4

. Aridus II

™

– Top View.

Completely loosen the three spring-loaded screws which attach the membrane

desolvator to the spray chamber oven. See Figure 6-5.

Membrane
Desolvator
Assembly

Содержание Aridus II































































Результаты поиска

Содержание Aridus II

Отзывы:

Похожие инструкции для Aridus II

Бренды по названию

Популярные бренды

CETAC Aridus II, Руководство оператора

Результаты поиска

Содержание Aridus II

Отзывы:

Похожие инструкции для Aridus II

Бренды по названию

Популярные бренды