CETAC Aridus II Скачать руководство пользователя страница 17

Страница: 17 / 62

Aridus II™ Operator’s Manual

Chapter 3: Installing the Aridus II™

Connecting the Aridus II

™

Drain Tubing

There is one liquid drain line to install on the back of the Aridus II

™

unit. To set

up this drain line:

Obtain the peri-pump tubing kit from the Aridus II

™

completion kit.

One bag inside the peri-pump tubing kit contains pre-cut tubing attached to

gray-gray color-coded peristaltic tubing. Remove this tubing from the bag.

One of the tubing assemblies contains a tan-colored PEEK nut. Install the

PEEK nut into the threaded port labeled DRAIN on the back of the Aridus II

™

unit. Tighten the PEEK nut so it is finger-tight.

Install the gray-gray color-coded peristaltic tubing (already attached to the

PEEK nut via a length of Teflon

tubing) to the peristaltic pump mounted on

the back of the Aridus II

™

unit. Note that liquid from the drain port should flow

to the bottom of the peristaltic pump and out the top to waste. This is shown

by the arrows next to the pump.

The outlet of the drain line may be placed in a suitable waste receptacle (such

as a beaker).

Close the shoe of the peristaltic pump and adjust the tension against the pump

rotor head with the spring-loaded screw.

Connecting the ASX-112FR Autosampler to the
Power Source

To connect the ASX-112FR autosampler to a power source:
A voltage-specific external desktop power supply is supplied with each ASX-

112FR autosampler.
To connect the autosampler to a power source, plug the external desktop

power supply cord into the power connector located on the back panel of the

autosampler. Then, plug the power supply’s power cord into the power supply

and into a 100–240-VAC ±10%, 50/60-Hz utility power outlet.
It is important to use the appropriate power cord for your country. Contact

CETAC Technologies if you need a different power cord.

FIRE AND SHOCK HAZARD
Use only the provided desktop power supply. The power supply must be
plugged into an outlet which has a protective ground connection.

WARNING

Содержание Aridus II































































Результаты поиска

Содержание Aridus II

Отзывы:

Похожие инструкции для Aridus II

Бренды по названию

Популярные бренды

CETAC Aridus II, Руководство оператора

Результаты поиска

Содержание Aridus II

Отзывы:

Похожие инструкции для Aridus II

Бренды по названию

Популярные бренды