background image

 

 

 

 

 

 

C650 & C650R User 

Manual Page 32 

7.

 

UPS MAINTENANCE  

 

 
UPS CARE 
 

For the best preventive maintenance: 
 

Keep the area around the equipment clean 
Keep the equipment free from dust  
Ensure the equipment is positioned in a well-ventilated area  
For maximum battery life keep the equipment at an ambient temperature of 20-25°C (77°F max) 
Carry out regular environmental and battery checks 

 
 

The batteries are rated for a 3–5-year service life. The service life varies depending on the frequency of usage 

and  ambient  temperature.  Batteries  used  beyond  expected  service  life  will  often  have  severely  reduced 
runtimes. Replace batteries at least every 4 years to keep units running at peak efficiency and prevent failure. 

 
 
 

7.1

 

TRANSPORTING THE UPS 

 

 

The  following  procedure  should  be  performed  or  supervised  by  personnel  knowledgeable  about  batteries 
and the required precautions. Keep unauthorised personnel away from batteries. If the UPS requires any type 
of transportation, the batteries must be disconnected (but not removed) before the unit is transported: 

 
 

Verify that the UPS is off and disconnected from mains power 
Place the UPS on a flat stable surface with the front of the cabinet facing you 
Remove the UPS front cover 
Disconnect the internal battery connectors 
Replace the UPS front cover 

 

To avoid damage and to prevent DOA’s always use a reputable courier for all equipment transportation. 
 
 

7.2

 

STORING THE UPS 

 

 
Where UPS equipment is stored for a long period, the batteries must be recharged every six months. The optimal 
storage VDC for VLRA batteries, depending on the environment is between 20-40%. This can be achieved by 
connecting the UPS to mains power.  
 

DO NOT 

Store the equipment in a warm, damp, dusty environment 

 

DO NOT 

Use the equipment if the batteries have not been recharged/if the recharge date exceeds six months  

 

DO NOT 

Expose the UPS to direct sunlight or source of heat 

 

 

DO 

Store the equipment in a cool, dry, clean environment  

 

DO 

Ensure the batteries are recharged every six months for a minimum of 48 hours 

 

DO 

Ensure EBMs are recharged every six months for a minimum of 3 hours 

 

 
 
 
 

 
 
 

ADOPTING A PREVENTATIVE MAINTENANCE SCHEDULE IS CRITICAL TO ACHIEVING OPTIMUM UPS PERFORMANCE 

 

THE INTERNAL UPS BATTERIES MUST BE DISCONNECTED BEFORE TRANSPORT

 

UPS BATTERIES MUST BE RECHARGED EVERY SIX MONTHS. ALWAYS CHECK THE BATTERY RECHARGE DATE ON THE 
SHIPPING CARTON BEFORE USE. 

 

Содержание C650








































Отзывы: