CertainTeed Bufftech Скачать руководство пользователя страница 10

Страница: 10 / 42

1. Getting Started

• Be sure to call underground prior to digging

• Assemble gates (if necessary) and decide where they

will be located

• Stake out the fence line

• Space and mark post hole locations for gate and sections

(spacer bar/template may be useful)

• Start at gate end post and work outward to determine

proper fence height relative to ground

2. Dig Holes

• Dig holes 30" deep or to frost line

- hole size for 5 x 5 posts = 12"
- hole size for 4 x 4 posts = 10"

• Clean holes and check for straight walls

3. Install First Post

• Insert post in hole

• Determine rough height

• Fill hole around post with concrete mix (sand, gravel

and cement) approximately 2" below grade

• Tamp concrete in hole to eliminate air pockets

• Level and square post

4. Install Bottom Rail

• Check bottom rail for drain holes

• Tape the ends of any rail being inserted into a post that is to

be filled with concrete to prevent concrete seepage

• Depress bullet clip, insert rail in post

• Bullet clip will drop down and hold rail into place

5. Install Second Post

• Insert second post in hole

• Insert bottom rail in post

• Insert block under bottom rail to position at correct

fence height

• Fill hole around second post with concrete mix

• Tamp, level and square fence

• Assembly may be continued by installing all bottom rails first,

or one section at a time

6. Support and Secure

• Level and square fence

• To lower a post, place a wood block from corner to corner on

the post and carefully tap with a mallet

• Never strike the PVC post without a wood support

7. Install Pickets and Rails

• Insert middle rail (if applicable) in post with large holes

facing down

• Insert pickets through holes in middle rail

• Insert pickets in bottom rail. Temporarily remove middle

rail ends from post. Insert top rail over pickets

• Insert middle rail and top rail in post

8. Secure Rails

• Square pickets and rails

• Check for even picket spacing on each end of rail

• Secure rail inside post with a #8 x 3/4" screw (do this on

both ends)

• Level middle rail, secure rail to pickets with (2) #8 x 1-1/2"

screws, snap caps and washers evenly spaced along rail

9. Hang Gate/Install Hardware

• For complete details, see gate installation instructions in

hardware box

• Position gate between posts

• Allow 1" gap for hinge and 3/4" for latch and gate swing

• Block up gate to square with fence; rails should be level

• Gate hardware must be mounted to two sides of the post

10. Solidify Gate Posts

• It is critical that gate hinge and latch posts are solid to ensure

proper gate functionality. Two methods are available:

A. Aluminum gate post stiffener

- Slide aluminum gate stiffener inside hinge, latch

or end posts with open end facing routed hole

- Drive a screw through the vinyl into the aluminum

stiffener at the bottom of the post to hold in place

- Insert post into ground

- Fill hole with concrete around outside of post

B. Concrete and rebar*

- Use two pieces of 1/2" rebar in each hinge, latch and

end post

- Rebar should extend from the bottom of the hole to

12" from the top of the post

- Hold rebar in opposite corners of post with rebar

separator clips

- Fill post with concrete mix to cover rebar and

hardware fasteners

- Tamp post with a rubber mallet to eliminate air pockets

- Leave gate on blocks for 72 hours to allow concrete to set

11. Install Caps

• Install post caps

• Caps may be secured with glue, silicone adhesive or

#8 x 3/4" screws, caps and washers

Contemporary Picket Fence

* Caution – In climates that experience freeze-thaw cycles, this installation method could result in post cracking over time. This would not be covered by the warranty.

Содержание Bufftech











































Результаты поиска

Содержание Bufftech

Отзывы:

Похожие инструкции для Bufftech

Бренды по названию

Популярные бренды

CertainTeed Bufftech, Руководство по установке

Результаты поиска

Содержание Bufftech

Отзывы:

Похожие инструкции для Bufftech

Бренды по названию

Популярные бренды