CertainTeed Bufftech Скачать руководство пользователя страница 26

Страница: 26 / 42

Privacy Fence
Norfolk 1

1. Getting Started

• Be sure to call underground prior to digging

• Assemble gates (if necessary) and decide where they will

be located

• Stake out the fence line

• Space and mark post hole locations for gate and sections

(spacer bar/template may be useful)

• Start at gate end post and work outward to determine

proper fence height relative to ground

2. Dig Holes

• Dig holes 30" deep or to frost line

- hole size for 5 x 5 posts = 12"

• Clean holes and check for straight walls

3. Install First Post

• Insert post in hole

• Determine rough height

• Fill hole around post with concrete mix (sand, gravel and

cement) approximately 2" below grade

• Tamp concrete in hole to eliminate air pockets

• Level and square post

4. Install Bottom Rail

• Tape the ends of any rail going into a post that is to be

filled with concrete to prevent concrete seepage

• Insert lock ring in both ends of bottom rail

• Depress lock ring tabs, insert bottom rail in post

• Tabs will recoil to hold rail in post

5. Install Second Post

• Insert second post in hole

• Insert bottom rail in post

• Insert block under bottom rail to position of correct

fence height

• Fill hole around second post with concrete mix

• Tamp, level and square fence

• Assembly may be continued by installing all bottom rails

first or one section at a time

6. Support and Secure

• Level and square fence

• To lower a post, place a wood block from corner to

corner of the post and carefully tap with a mallet

• Never strike the PVC post without a wood support

7. Install Pickets and Rails

• Insert pickets in bottom rail

• Insert top rail over pickets

• Depress lock ring tabs, insert top rail in post

• Insert midrail into posts

• Secure midrail on both sides through the same picket

with (2) #8 x 1-1/2" screws, snap caps and washers

8. Hang Gate/Install Hardware

• For complete details, see gate installation instructions in

hardware box

• Position gate between posts

• Allow 1" gap for hinge and 3/4" for latch and gate swing

• Block up gate to square with fence; rails should be level

• Gate hardware must be mounted to two sides of the post

9. Solidify Gate Posts

• It is critical that gate hinge and latch posts are solid to

ensure proper gate functionality. Two methods are avail-

able:

A. Aluminum gate post stiffener

- Slide aluminum gate stiffener inside hinge,

latch or end posts

- Drive a screw through the vinyl into the aluminum

stiffener at the bottom of the post

- Insert post into the ground

- Fill hole with concrete around outside of post

B. Concrete and rebar*

- Use two pieces of 1/2" rebar in each hinge, latch and

end post

- Rebar should extend from the bottom of the hole to

12" from the top of the post

- Hold rebar in opposite corners of post with rebar

separator clips

- Fill post with concrete mix to cover rebar and

hardware fasteners

- Tamp post with a rubber mallet to eliminate air pockets

- Leave gate on blocks for 72 hours to allow concrete

to set

10. Install Caps

• Install post caps

• Caps may be secured with glue, silicone adhesive or

#8 x 3/4" screws, caps and washers

* Caution – In climates that experience freeze-thaw cycles, this installation method could result in post cracking over time. This would not be covered by the warranty.

For accents, see page 30

Содержание Bufftech











































Результаты поиска

Содержание Bufftech

Отзывы:

Похожие инструкции для Bufftech

Бренды по названию

Популярные бренды

CertainTeed Bufftech, Руководство по установке

Результаты поиска

Содержание Bufftech

Отзывы:

Похожие инструкции для Bufftech

Бренды по названию

Популярные бренды