CertainTeed Bufftech Скачать руководство пользователя страница 40

Страница: 40 / 42

Insert 5/8" bearing over router bit shank.

Bearing will follow cut out in template.

outside holes Fit

OVER 5 X 5 POST

inside

holes Fit

OVER

4 X 4 POST

Routing template kit can be used to

enlarge holes for racking as well as

to create transitions for stepping,

changing heights or styles.

Install 3/8" router blade and 5/8"

bearing or router guide. Any substitu-

tions may result in improper hole size

or damage to the template kit.

note: Template cutout size is

designed to be 1/8” larger

than the finished cut to allow

bearing to follow the shape.

Select the appropriate template for

the application.

Assemble the template as shown,

configured for the desired post size

(4" or 5").

note: It is advisable to practice

routing on a scrap piece

before attempting actual cut.

Mark location of hole to be routed.

Offset template cut by 1/8" to allow for

bearing (i.e., if hole is to be located

3" from top of post, position edge of

template 2-7/8" from top).

Tighten wing nuts. Place on a flat,

firm surface to prevent tipping.

Route hole per manufacturer’s

recommendations.

ALWAYS WEAR SAFETY GLASSES.

Loosen wing nut and remove template.

For situations that require a larger

hole to accommodate racking, route a

standard hole, loosen wing nuts and

slide template to new position to route

excess material.

a
b
c

ROUTING TEMPLATE

1-1/8" TEMPLATE SPACER PLATE

1-1/2" TEMPLATE SPACER PLATE

1/4" -20 X 6" BOLTS

3/8" OD PLEXI TUBE

1/4" FLAT WASHER

1/4" -20 WING NUT

3/8" ROUTER BIT W/ 1/4" SHANk

5/8" BEARING W/ 1/4" ID OPENING

g
h

Post Routing Template Kit

Содержание Bufftech











































Результаты поиска

Содержание Bufftech

Отзывы:

Похожие инструкции для Bufftech

Бренды по названию

Популярные бренды

CertainTeed Bufftech, Руководство по установке

Результаты поиска

Содержание Bufftech

Отзывы:

Похожие инструкции для Bufftech

Бренды по названию

Популярные бренды