Cerio DT-300N Скачать руководство пользователя страница 105

Страница: 105 / 164



IP Address :

The IP address of the WAN port



IP Netmask :

The Subnet mask of the WAN port



PPTP Server IP Address :

The IP address of the PPTP server



User Name :

Enter User Name for PPTP connection



Password :

Enter Password for PPTP connection



Reconnect Mode :

Always on

– A connection to Internet is always maintained.

On Demand

– A connection to Internet is made as needed.

Manual

– Click the “

Connect

” button on “

WAN Information

” in the Overview page

to connect to the Internet.



Idle Time :

Time to last before disconnecting PPPoE session when it is idle. Enter

preferred Idle Time in minutes. Default is “

”, indicates disabled. When Idle time is

disabled, the “

Reconnect

Mode

” will turn out “

Always

”



MTU :

By default, it’s

1460

bytes. MTU stands for Maximum Transmission Unit.

Consult with WISP for a correct MTU setting.

When Time Server is enabled at the “On Demand” mode, the

“Reconnect Mode” will turn out “Always on”

Содержание DT-300N





































































































































































Результаты поиска

Содержание DT-300N

Отзывы:

Бренды по названию

Популярные бренды

Cerio DT-300N, Руководство пользователя

Результаты поиска

Содержание DT-300N

Отзывы:

Бренды по названию

Популярные бренды