Century Heating CW2900 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 60

background image

CW2900 Installation and Operation Manual

41

8 The Venting System

8.1 General

The venting system, made up of the chimney and the liner inside the chimney, acts as the
engine that drives your wood heating system. Even the best insert will not function safely
and efficiently as intended if it is not connected to a suitable chimney and liner system.

The heat in the flue gases that pass from the insert into the chimney is not waste heat.
This heat is what the chimney uses to make the draft that draws in combustion air, keeps
smoke inside the insert and safely vents exhaust to outside. You can think of heat in the
flue gas as the fuel the chimney uses to make draft.

8.2 Block-Off Plate

To reduce the possibility of a cold air draft from the masonry chimney to get into the room
when  the  insert  in  not  working,  the  installation  of  a  sheet  metal  block-off  plate  ((A)  in  the
drawing  below)  is  recommended.  Once  you  have  made  the  block-off  plate  to  the  proper
dimension,  cut  the  pipe  hole  slightly  larger  than  the  liner’s  diameter  and  then  install  the
liner through this hole. Set the Block-off plate in place and secure with masonry nails into
mortar joints. Finally, seal the joints between the plate and the wall with high temperature
silicone, and then use stove-furnace cement to seal between the pipe and the hole.

In Canada, CSA B365 Standard permits the use of ‘’Roxul’’ type wool stuffed around the
liner as it passes through the throat area as an alternative to a sheet metal Block-off plate.
However, this method is inferior to the use of a sheet metal block-off plate.

«
...
39
40
41
42
43
...
»

Содержание CW2900





























































Отзывы:

Нет отзывов

Похожие инструкции для CW2900

COLLETTE L-FT629PST-A

Бренд: HAMPTON BAY Страницы: 6

Бренд: HAMPTON BAY Страницы: 48

Бренд: Valor Страницы: 5

Бренд: Saey Страницы: 44

Бренд: Klarstein Страницы: 76

Бренд: Empire Comfort Systems Страницы: 8

Бренд: GreenSmart Страницы: 26

Бренд: FireplaceXtrordinair Страницы: 24

Бренд: Archgard Страницы: 26

Бренд: Jensen Страницы: 54

Бренд: Paramount Fitness Страницы: 24

SCANDIC DELUXE SDC20RC

Бренд: Dimplex Страницы: 4

Бренд: Twin-Star International Страницы: 22

Бренд: Paramount Fitness Страницы: 9

Бренд: Dru Страницы: 24

21 DV Wilmington Face

Бренд: Lopi Страницы: 3

Бренд: Signature Design by Ashley Страницы: 39

Бренд: Vermont Castings Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды