Century Heating CW2900 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 60

background image

CW2900 Installation and Operation Manual

19

IF YOU MUST OPEN THE DOOR WHILE THE FUEL IS FLAMING, OPEN THE AIR
CONTROL FULLY FOR A FEW MINUTES, THEN UNLATCH AND OPEN THE DOOR
SLOWLY.

3.4.2 Ash Removal

Ash should be removed from the firebox every two or three days of full time heating. Do
not let the ash build up in the firebox because it will interfere with proper fire management.

The best time to remove ash is after an overnight fire when the insert is relatively cool, but
there is still some chimney draft to draw the ash dust into the insert and prevent it from
coming into the room.

After  ashes  have  been  removed  from  the  insert  and  placed  in  a  tightly  covered  metal
container, they should be taken outside immediately. The closed container of ashes should
be  placed  on  a  non-combustible  floor  or  on  the  ground  well  away  from  all  combustible
materials pending final disposal. Ashes normally contain some live charcoal that can stay
hot  for  several  days.  If  the  ashes  are  disposed  of  by  burial  in  soil  or  otherwise  locally
dispersed, they should be retained in the closed container until all cinders have thoroughly
cooled. Other waste should not be placed in this container.

NEVER STORE ASHES INDOORS OR IN A NON-METALIC CONTAINER OR ON A
WOODEN DECK.

3.4.3 Raking Charcoal

Rekindle the fire when you notice that the room temperature has fallen. You will find most
of the remaining charcoal at the back of the firebox, furthest from the door. Rake these
coals towards the door before loading. There are two reasons for this raking of the coals.
First, it concentrates them near where most of the combustion air enters the firebox and
where they can ignite the new load quickly, and second, the charcoal will not be smothered
by the new load of wood. If you were to simply spread the charcoal out, the new load will
smoulder for a long time before igniting.

Remove ash first, and then rake charcoal towards the front of the firebox before loading so
that it will ignite the new load.

«
...
17
18
19
20
21
...
»

Содержание CW2900





























































Отзывы:

Нет отзывов

Похожие инструкции для CW2900

Paul Agnew Designs ilektro Series

Бренд: Living Fire Страницы: 4

Бренд: Valor Страницы: 3

Бренд: OVE Страницы: 16

Бренд: FBR Страницы: 30

Бренд: Majestic fireplaces Страницы: 24

Бренд: HASE Страницы: 48

Бренд: Heatmaster Страницы: 26

MSS136144273001

Бренд: Mainstays Страницы: 16

Бренд: Firesense Страницы: 18

Бренд: Bond Страницы: 42

Бренд: Napoleon Страницы: 3

BH47-093-999-32

Бренд: Better Homes and Gardens Страницы: 8

Бренд: Heat & Glo Страницы: 26

Бренд: Nordpeis Страницы: 48

Бренд: Coleman Страницы: 2

Бренд: Coleman Страницы: 8

Бренд: Laminvale Страницы: 9

Бренд: Modern Flames Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды