Century Heating CW2900 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 60

background image

CW2900 Installation and Operation Manual

21

3.5 Fan Operation

Allow the insert to reach operating temperature (approximately one hour), before turning
on the fan, since increased airflow from the fan will remove heat and affect the start-up
combustion efficiency.

NOTE: ENSURE THE FAN CORD IS NOT IN CONTACT WITH ANY SURFACE OF THE
INSERT TO PREVENT ELECTRICAL SHOCK OR FIRE DAMAGE. DO NOT RUN CORD
BENEATH THE INSERT.

Turn the fan ON or OFF with the variable speed control located on the right side of the fan
assembly next to the bottom louvre. The switch settings are Off, High and adjustable
down to Low.

3.5.1 Building Different Fires for Different Needs

Using  the  air  control  is  not  the  only  way  to  match  the  insert’s  heat  output  to  the  heat
demand.  Your  house  will  need  far  less  heat  in  October  than  in  January  to  be  kept  at  a
comfortable  temperature.  If  you  fill  the firebox  full  in  fall  weather,  you  will  either  overheat
the space or turn the insert down so much that the fire will be smoky and inefficient. Here
are some suggestions for building fires to match different heat demand.

3.5.1.1 Small Fires to Take the Chill off the House

To build a small fire that will produce a low heat output, use small pieces of firewood and
load them crisscross in the firebox. The pieces should be only 3” to 4” in diameter. After
raking the coals, you can lay two pieces parallel to each other corner to corner in the
firebox and lay two more across them in the other direction. Open the air control fully and
only reduce the air after the wood is fully flaming. This kind of fire is good for mild weather
when you are around to tend the insert and should provide enough heat for four hours or

«
...
19
20
21
22
23
...
»

Содержание CW2900





























































Отзывы:

Нет отзывов

Похожие инструкции для CW2900

Бренд: Dimplex Страницы: 63

Бренд: barbas Страницы: 44

Бренд: Wamsler Страницы: 84

Бренд: HAMPTON BAY Страницы: 19

Бренд: stellar labs Страницы: 50

Majestic Oak Series

Бренд: Majestic fireplaces Страницы: 2

Бренд: FACTO Страницы: 10

FBD400RTCC-M-HC/MO

Бренд: Procom Страницы: 36

Бренд: crystal fires Страницы: 26

Бренд: RAIS Страницы: 11

Бренд: Nibe Страницы: 4

Бренд: Red Fire Страницы: 17

Бренд: Xaralyn Страницы: 2

Бренд: Xaralyn Страницы: 10

Бренд: Woodbridge Fireplace Inc Страницы: 20

Бренд: White Mountain Hearth Страницы: 4

Бренд: Monessen Hearth Страницы: 20

WOODBURNING FIREPLACE 424WBST

Бренд: Monessen Hearth Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды