Century Heating 45398A Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 47

background image

38

For the FW700 and the FW3000 model, we suggest that you operate it with the air control slightly
open (approximately 10%) to achieve an optimum efficiency. Make sure that you have a good fire
going and an adequate ember bed before you completely close the air control. Use a chimney
thermometer if necessary. Closing the air control too soon will lower combustion efficiency and may
cause the fire to die out.

In all Century appliances the addition of a blower is highly recommended to maximize your unit’s
efficiency.

3.6 FAN (BLOWER) OPERATION

If you have purchased and installed and optional fan (blower), allow the stove to reach operating
temperature (approximately one hour), before turning on the fan. The increased airflow from the fan
will cool the firebox and affect the start-up combustion efficiency if the fan is turned on too quick.

CAUTION

:

ENSURE THAT THE FAN

’

S POWER CORD IS NOT IN CONTACT WITH ANY SURFACE OF THE TTOVE

TO PREVENT ELECTRICAL SHOCK OR FIRE DAMAGE

.

DO NOT RUN THE POWER CORD BENEATH THE STOVE

.

«
...
37
38
39
40
41
...
»

Содержание 45398A
















































Отзывы:

Нет отзывов

Похожие инструкции для 45398A

Бренд: Jøtul Страницы: 32

Бренд: Jøtul Страницы: 40

CITY GRUNDI Maxi

Бренд: BRULA Страницы: 17

Бренд: barbas Страницы: 32

Бренд: Panadero Страницы: 12

Бренд: Desa Страницы: 28

Бренд: Last Calor Страницы: 153

Бренд: Whitfield Страницы: 35

Бренд: Century Hearth Страницы: 2

Бренд: Century Hearth Страницы: 2

Бренд: Koper Страницы: 12

Бренд: Bimar Страницы: 44

Baby Countryside

Бренд: Magnum Страницы: 44

Бренд: USSC Страницы: 28

Бренд: Lofty Страницы: 16

Бренд: RAIS Страницы: 13

Бренд: RAIS Страницы: 40

Бренд: HWAM Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды