Century Heating 45398A Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 47

background image

1

INTRODUCTION

Stove Builder International, one of the most important wood stove and fireplace manufacturers in
North America, congratulates you on your purchase and wishes to help you get maximum
satisfaction from your wood stove. In the pages that follow, we will give you advice on wood
heating and controlled combustion as well as technical specifications regarding installation,
operation and maintenance of the model you have chosen.

The instructions pertaining to the installation of your wood stove in North America comply with
ULC-S627 and UL-1482 standards.

Read this entire manual before you install and use your new stove. If this stove is not properly
installed, a house fire may result. To reduce the risk of fire, follow the installation instructions.
Failure to follow instructions may result in property damage, bodily injury, or even death.

Consult your municipal building department or fire officials about restrictions and installation
requirements in your area and the need to obtain a permit.

K

EEP THIS INSTRUCTIONS MANUAL FOR FUTURE REFERENCE

.

CAUTIONS:

•

HOT WHILE IN OPERATION

.

KEEP CHILDREN

,

CLOTHING AND FURNITURE AWAY

.

CONTACT MAY

CAUSE SKIN BURNS

.

•

DO NOT USE CHEMICALS OR FLUIDS TO IGNITE THE FIRE

.

•

DO NOT LEAVE THE STOVE UNATTENDED WHEN THE DOOR IS SLIGHTLY OPENED DURING IGNITION

.

•

DO NOT BURN WASTE

,

FLAMMABLE FLUID SUCH AS GASOLINE

,

NAPHTHA

,

OR MOTOR OIL

.

•

DO NOT CONNECT TO ANY AIR DISTRIBUTION DUCT OR SYSTEM

.

•

ALWAYS CLOSE THE DOOR AFTER IGNITION

.

•

D

O NOT INSTALL IN A MOBILE HOME

REGISTER YOU WARRANTY ONLINE

To receive full warranty coverage, you will

need to show evidence of the date you

purchased your stove. Keep your sales

invoice. We also recommend that you register

your warranty online at

www.century-heating.com

Registering your warranty online will help us

track rapidly the information we need on your

stove.

«
1
2
3
4
...
»

Содержание 45398A
















































Отзывы:

Нет отзывов

Похожие инструкции для 45398A

Бренд: Faber Страницы: 15

HRV 140 Silhouette

Бренд: Ravelli Страницы: 76

Advance Pellet Stove

Бренд: Harman Страницы: 44

Бренд: LISEO Страницы: 12

CLASSIC 400 Top Duo

Бренд: Harvia Страницы: 18

Бренд: Morso Страницы: 24

Бренд: Stanley Страницы: 24

Бренд: RAIS Страницы: 275

Бренд: Residential Retreat Страницы: 60

PORTA OVEN PRO 40

Бренд: CPL Страницы: 6

Бренд: England's Stove Works Страницы: 17

Бренд: England's Stove Works Страницы: 61

Бренд: England's Stove Works Страницы: 61

Бренд: Seefire Страницы: 10

Бренд: NESTOR MARTIN Страницы: 88

Бренд: Palazzetti Страницы: 164

Бренд: Palazzetti Страницы: 10

Havelock GDS50-1NSB

Бренд: Napoleon Страницы: 108

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды