background image

4

5 . Locate the azimuth adjustment screws on the equatorial 

mount (Fig 2-3) .

6 . Retract the screws so they do not extend into the azimuth 

housing on the mount . 

7 . Hold the equatorial mount over the tripod adapter so that 

the azimuth housing is above the metal peg .

8 . Lower the equatorial mount on the tripod so that the two  

are flush .

9 . Thread the knob (attached to the central rod) on the 

underside of the tripod head into the bottom of the 

equatorial mount to hold it firmly in place . 

i

nStallinG

 

thE

 C

ountErWEiGht

 b

ar

To properly balance the telescope, the mount comes with a 

counterweight bar and at least one counterweight (depending 

on model) . To install the counterweight bar:
1 . Locate the counterweight bar locking nut from the box 

containing the CGEM DX mount (see Fig 2-5) .

2 . Thread the counterweight bar through the rounded end of 

locking nut until the threads pass all the way through and the 

locking nut can go no further .

3 . Locate the opening in the equatorial mount on the DEC axis .

4 . Thread the counterweight bar into the opening until tight .
5 . Tighten the counterweight bar lock nut fully for  

added support .

Once the bar is securely in place you are ready to attach  

the counterweight .

Since the fully assembled telescope can be quite 

heavy, position the mount so that the polar axis is 

pointing towards north before the tube assembly and 

counterweights are attached. This will make the polar 

alignment procedure much easier.

i

nStallinG

 

thE

 C

ountErWEiGht

Depending on which telescope model you have, you will 

receive either one, two or three counterweights . To install  

the counterweight(s):
1 . Orient the mount so that the counterweight bar points 

toward the ground 

2 . Remove the counterweight safety screw on the end of the 

counterweight bar (i .e ., opposite the end that attaches to  

the mount) .

3 . Loosen the locking screw on the side of the counterweight . 
4 . Slide the counterweight onto the shaft (see Figure 2-5) .
5 . Tighten the locking screw on the side of the weight to hold 

the counterweight in place . 

6 . Replace the counterweight safety screw .

F

igure

 2-4

Equatorial 

Mount

Alignment 

Peg

Tripod 

Mounting 

Adapter

Heavy 

Duty 

Tripod

Center 

Support 

Rod

Tripod 

Head

F

igure

 2-5 – M

ount

 

shown

 

with

 

two

 

Counterweights

 

(CgeM DX 1400)

Counterweight  

Bar Locking Nut

Counterweight Bar

Locking  

Screw

Counterweight

Safety Screw

Содержание CGEM DX







































Отзывы: