Cedar Summit STONEYCREEK CEDAR PLAYHOUSE P280090 Скачать руководство пользователя страница 2

Warnings and Safe Play Instructions

CONTINUOUS ADULT SUPERVISION REQUIRED. Most serious injuries and deaths on playground equipment have 
occurred while children were unsupervised! Our products are designed to meet mandatory and voluntary safety standards. 
Complying with all warnings and recommendations in these instructions will reduce the risk of  serious or fatal injury to children 
using this play system. Go over the warnings and safe play instructions regularly with your children and make certain that they 
understand and follow them. Remember on-site adult supervision is required for children of  all ages.

   Dress children with well fitting and full foot enclosing 

footwear.

   Check for splintered, broken or cracked wood; 

missing, loose, or sharp edged hardware. Replace, 
tighten and or sand smooth as required prior to 
playing.

   Do not allow children to wear open toe or heel 

footwear like sandals, flip–flops or clogs.

   Do not permit climbing on equipment when it is wet.

   Do not permit rough play or use of  equipment in a 

manner for which it was not intended. Standing or 
climbing on or jumping from the roof.

WARNING

 – Safe Play Instructions   

CHOKING HAZARD/SHARP EDGES & POINTS

Adult assembly required. This product contains small
parts and parts with sharp edges and points. Keep parts 
away from children until fully assembled.

STRANGULATION HAZARD

• 

 NEVER

 allow children to play with ropes, 

clotheslines, pet leashes, cables, chains or cord-like 
items when using this playhouse or to attach these 
items to the playhouse.

• 

 NEVER

 allow children to wear loose fitting clothing, 

ponchos, hoods, scarves, capes, necklaces, items with 
draw-strings, cords or ties when using this playhouse.

•  

NEVER

 allow children to wear bike or sport helmets 

when using this playhouse.

Failure to prohibit these items, even helmets with chin 
straps, increases the risk of  serious injury and death to 
children from entanglement and strangulation.

TIP OVER HAZARD

Choose a level location for the equipment. This can 
reduce the likelihood of  the playhouse tipping over 
and loose-fill surfacing materials washing away during 
heavy rains.

DO NOT allow children to play on the playhouse until 
the assembly is complete.

WARNING

 

Instructions for Proper Maintenance

Your Cedar Summit Play System is designed and constructed of  quality materials with your child’s safety in mind. As 
with all outdoor products used by children, it will weather and wear. To maximize the enjoyment, safety and life of  your 
Playhouse, it is important that you, the owner, properly maintain it.

HARDWARE:

   Check metal parts for rust. If  found, 

sand and repaint using a non-lead paint 
complying with 16 CFR 1303.

   Inspect and tighten all hardware. On 

wood assemblies DO NOT OVER-
TIGHTEN as to cause crushing and 
splintering of  wood.

   Check for sharp edges or protruding screw threads, add 

washers if  required.

WOOD PARTS:

   Check all wood members for deterioration, structural 

damage and splintering. Sand down splinters and replace 
deteriorated wood members. As with all wood, some 
checking and small cracks in grain is normal.

   Applying a water repellent or stain (water-based) on a yearly 

basis is important maintenance to maintain maximum life 
and performance of  the product.

Check the following at the beginning of the play season:

Check twice a month during play season:

HARDWARE:

   Inspect for tightness. Must be firmly against, but not crushing the wood. 

DO NOT OVER-TIGHTEN.  This will cause splintering of  wood.

   Check for sharp edges or protruding 

screw threads.  Add washers if  required.

If you dispose of your playhouse:

 Please disassemble and dispose of  your unit so that it does not create any unreasonable 

hazards at the time it is discarded. Be sure to follow your local waste ordinances.

 

[email protected]   

Содержание STONEYCREEK CEDAR PLAYHOUSE P280090





























































Отзывы: