Cedar Summit F23135 Скачать руководство пользователя страница 52

Страница: 52 / 92

[email protected]

35 x

#8 x 1-1/2” Wood Screw

Step 19: Large Roof Support Assembly

Part 3

Place the assembly on a hard, flat surface, then on the inside place (2172) Gable Top tight to the top of (2244)

Large Support and (2243) Large Support L at the peak and 2 (2176) Gable Uprights so they are tight to (2240)

Gable Bottom, (2244) Large Support and (2243) Large Support L. The distance between (2176) Gable Uprights

should be 13-3/8”. (fig. 19.5)

Starting flush to the inside edge of each (2176) Gable Upright attach 1 (2173) Window Gable flush to the top of

each (2244) Large Support and (2243) Large Support L. Follow with 1 (2171) Gable A then 1 (2170) Gable B per

side. (fig. 19.6)

Flush to the bottom of (2172) Gable Top and tight to each (2173) Window Gable place (2255) Gable Band. (fig.

19.6)

Attach boards to supports, uprights and Gable Top and Bottom with (S2) #8 x 1-1/2” Wood Screws, 4 per

(2170) Gable B and (2171) Gable A; 6 per (2173) Window Gable and 7 in (2255) Gable Band. (fig. 19.6)

Wood Parts

Hardware

2170

2 x

Gable Upright 5/4 x 2 x 12-1/16”

1 x

Gable Top 5/4 x 6 x 11”

2 x

Window Gable 1 x 5 x 18-3/8”

2 x

Gable A 1 x 5 x 13-7/8”

2176

2255

2172

2 x

Gable B 1 x 6 x 9-3/8”

1 x

Gable Band 1 x 4 x 13-3/8”

2171

2172

2173

2255

2170

2244

2243

Fig. 19.5

2240

Fig. 19.6

2176

2172

2244

2243

2240

(hidden on

this side)

2170

2171

2173

x 35

Inside View

Flush

13-3/8”

Содержание F23135





























































































Результаты поиска

Содержание F23135

Отзывы:

Похожие инструкции для F23135

Бренды по названию

Популярные бренды

Cedar Summit F23135, Инструкция по установке и эксплуатации

Результаты поиска

Содержание F23135

Отзывы:

Похожие инструкции для F23135

Бренды по названию

Популярные бренды