Cedar Summit F23135 Скачать руководство пользователя страница 45

Страница: 45 / 92

[email protected]

6 x

#8 x 1-1/2” Wood Screw

6 x

#6 x 5/8” Pan Screw

Step 18: Door Wall Assembly

Part 2

Tight to the bottom of (2186) Back Front Wall and flush to the outside edges of (2180) Post and (2182) Mid

Post attach (2166) Door Arch to (2180) Post, (2179) Door Post and (2182) Mid Post with 6 (S2) #8 x 1-1/2” Wood

Screws. (fig. 18.4)

In the opening for the door between (2179) Door Post and (2182) Mid Post, measure 5/8” up from the top of

(2178) Ground Front then attach remaining side of the Door Hinges on (8197) Door Panel to (2182) Mid Post with

3 (S13) #6 x 5/8” Pan Screws per hinge. (fig. 18.4 and 18.5)

S13

8197

S13

Hardware

Wood Parts

1 x

Door Arch 1 x 6 x 55-1/4”

2166

5/8”

S13

2182

2180

2179

2178

2166

2186

8197

2166

Fig. 18.4

Fig. 18.5

Door

Hinge

Door

Hinge

Notice bolt

hole location

Содержание F23135





























































































Результаты поиска

Содержание F23135

Отзывы:

Похожие инструкции для F23135

Бренды по названию

Популярные бренды

Cedar Summit F23135, Инструкция по установке и эксплуатации

Результаты поиска

Содержание F23135

Отзывы:

Похожие инструкции для F23135

Бренды по названию

Популярные бренды