Cedar Summit F23135 Скачать руководство пользователя страница 32

Страница: 32 / 92

[email protected]

Step 10: Swing Wall Assembly

Part 1

2 x

1/4 x 2” Hex Bolt (1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

4 x

1/4 x 4” Hex Bolt (1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

2 x

1/4 x 4-1/2” Hex Bolt (1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

1 x

SW Ground 1 x 5 x 75-3/8”

1 x

SW End 5/4 x 6 x 38-1/2”

2 x

Lower Diagonal 2 x 3 x 37”

2184

0369

2188

Fig. 10.1

0369

2180

2188

With at least one adult helper hold up the Front and Back Walls and loosely attach (2184) SW Ground using

4 (H4) 1/4 x 4” Hex Bolts (with lock washer, flat washer and t-nut) and (2188) SW End using 2 (H5) 1/4 x 4-1/2”

Hex Bolts (with lock washer, flat washer and t-nut), in the top holes, to both (2180) Posts. (fig. 10.1 and 10.2)

Loosely attach 1 (0369) Lower Diagonal to each end of (2184) SW Ground with 1 (H2) 1/4 x 2” Hex Bolt (with

lock washer, flat washer and t-nut) per diagonal. (fig. 10.1 and 10.2)

2184

1/4” lock

washer

1/4” flat

washer

1/4”

t-nut

Hardware

Wood Parts

Fig. 10.2

0369

Notice hole

locations

2180

Front Wall

Back Wall

Содержание F23135





























































































Результаты поиска

Содержание F23135

Отзывы:

Похожие инструкции для F23135

Бренды по названию

Популярные бренды

Cedar Summit F23135, Инструкция по установке и эксплуатации

Результаты поиска

Содержание F23135

Отзывы:

Похожие инструкции для F23135

Бренды по названию

Популярные бренды