CE+T Power BRAVO 10 - 48/120 Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 59

CE+T Power BRAVO 10 - 48/120 Скачать руководство пользователя страница 48

12. Maintenance

Maintenance shall only be performed by properly trained people.

12.1 Access Inview with Laptop

•

Download system LOG FILE and save.
- Analyze log file and correct errors.

•

Download system CONFIGURATION FILE and save.
- Check/correct configuration file according to operation conditions.
- Check/correct alarm configuration.

•

Check module internal temperature for deviation between modules.
- Temperature deviation may indicate build up of dust. Clean the module by air suction blower or vacuum
cleaner.

•

Check module/system load.

•

Check/Correct inverter mapping (DC group/AC group/ Address).

•

Change configuration file to validate that system operates on both supply sources.

•

Check outgoing alarm, consult configuration file what actions will generate alarm.

12.2 Manual check

•

Validate input voltage (AC input, DC input, AC output) with multi-meter.

•

Replace dust filter.

12.3 Optional

•

With an infrared camera check termination hot spots.
- Tighten terminations.

Maintenance

48

- Bravo 10 - 48/120 - User manual - v1.1

«
...
46
47
48
49
50
...
»

Содержание BRAVO 10 - 48/120




























































Отзывы:

Нет отзывов