CE+T Power BRAVO 10 - 48/120 Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 59

CE+T Power BRAVO 10 - 48/120 Скачать руководство пользователя страница 43

9. Finishing

•

Make sure that the sub-rack/cabinet is properly fixed to the cabinet/floor.

•

Make sure that the sub-rack/cabinet is connected to Ground.

•

Make sure that all DC and AC input breakers are switched OFF.

•

Make sure that all cables are according to recommendations and local regulations.

•

Make sure that all cables are strained relived.

•

Make sure that all breakers are according to recommendation and local regulations.

•

Make sure that DC polarity is according to marking.

•

Re tighten all electrical terminations.

•

Make sure that no inverter/controller positions are left open.

•

Cover empty inverter positions with dummy cover.

•

Make sure that the Remote ON/OFF is appropriately wired according to local regulations.

•

Make sure that the point of AC supply meets local regulations.

Finishing

43

- Bravo 10 - 48/120 - User manual - v1.1

«
...
41
42
43
44
45
...
»

Содержание BRAVO 10 - 48/120




























































Отзывы:

Нет отзывов