CCS DIL-5000-WV Скачать руководство пользователя страница 14

Страница: 14 / 16

Symptom

What to inspect, and repair

In case of operation panel

In case of external control

(serial communications)

Lights not

illuminating.

Is the power supply turned ON?
Is the light-side cable connected to an output connector for the light corresponding

to the type?

Reference page: p. 6

Is the trunk cable (for the light) properly

connected?

Is the break out cable properly

connected? Check for the connector

connection, and then rectify the

connection.

Reference page: p. 8

Lights not turning

OFF.

Light control data is set to “0”, but the light does not turn OFF.

There is a possibility of product failure.

Please stop the usage, turn off the power. Please do not attempt to use the product

when it fails or to repair by customers, since it is dangerous, but contact CCS Inc.

(please refer the back cover)

Lights unable to

control.

Is a wrong channel selected? Check for a channel to exercise light control.

Reference page: p. 10

Reference page: p. 15

Is the unit set to external control?

If so, set to manual control on the

operation panel.

Is the break out cable properly

connected? Check for the connector

connection, and then rectify the

connection.

Reference page: p. 24

Reference page: p. 8

Is the light control setting correct ?

Check the setting method, and then resetting of the light control data.

Reference page: p. 11

Reference page: p. 15

There is a possibility of product failure.

Please contact CCS Inc. (please refer to

the back cover)

Is there any errors in communication

setting?

Check for the protocol, then reset.

Reference page: p. 13

Light flickers

(blinks).

Is the light connected securely to output connector?

Please insert the connector until you hear clicking sound.

Reference page: p. 8

There is a possibility of product failure.

Please contact CCS Inc. (please refer to

the back cover)

Is the break out cable properly

connected? Check for the connector

connection, and then rectify the

connection.

Reference page: p. 8

Troubleshootings

Symptom

What to inspect, and repair

In case of operation panel

In case of external control

(serial communications)

Light is dark.

Is the light control setting correct ?

Check the setting method, and then resetting of the light control data.

Reference page: p. 11

Reference page: p. 15

There is a possibility of product failure.

Please contact CCS Inc. (please refer to

the back cover)

Is the shutter timing of the In-Sight5000

series vision sensor, out of light pulse?

Make setting of delay time with the serial

communication command.

Reference page: p. 14

Malfunctioning

Is the break out cable properly connected?

Check for the connector connection, and then rectify the connection.

Reference page: p. 8

If the situation does not improve, or unexpected situation occurs, please contact

CCS Inc. (please refer to the back cover)

Fuming, extreme

temperature,

smell, noise,

or other

abnormality.

There is a possibility of product failure.

Please stop the usage, turn the power off. Please do not attempt to use the product

when it fails or to repair by customers, since it is dangerous, but contact CCS Inc.

(please refer the back cover).

Troubleshootings

If you have any problems during product usage, please look up the cause in this chart.

If the situation does not improve, or unexpected situation occurs, please contact CCS

Inc. (please refer to the back cover)

Symptom

What to inspect, and repair

In case of setting Job

The luminance of

the scene called

is different from

that of the light.

The set values of Snippet may not match up with the data saved in the internal

memory of the DIL interface unit. Re-register scene data.

Reference page: p. 23

Setting was

made but it is

not reflected in

lighting.

After the completion of making a variety of settings, transmit data to the DIL interface

unit. Unless the data are transmitted to the DIL interface unit, they will not be

reflected.

Reference page: p. 23

While in strobe

light mode, light

pulse is out of

timing for the

camera shutter.

Delay light pulse timing to match it up with the camera shutter timing.

Make setting of delay time while in strobe setting mode.

Reference page: p. 22

Troubleshootings

Содержание DIL-5000-WV

















Результаты поиска

Содержание DIL-5000-WV

Отзывы:

Похожие инструкции для DIL-5000-WV

Бренды по названию

Популярные бренды

CCS DIL-5000-WV, Руководство пользователя

Результаты поиска

Содержание DIL-5000-WV

Отзывы:

Похожие инструкции для DIL-5000-WV

Бренды по названию

Популярные бренды