9
Alternately the user can change to the f ollowing mode
:
On dialing an engaged extension user would get engaged tone. During the engaged tone user can FLASH and get
connected to the Junction line.
Programming
:
Dial #
0000 + 831 #
To shif t back to the def ault setting, Dial #
0000 + 830 #
.
Junction Dialing Delay Time
.
This is the time af ter the last digit dialed by an extension on Junction Line.
It is 7 secs in def ault.
The PBX assumes call maturity f rom af ter the lapse of this time.
The FLASH f unction to hold an Incoming Junction call starts working af ter the lapse of this time.
To change this delay time, Dial #
0000 + 03 TT # Where, TT= 01 to 99 secs. Def ault value = 07 (7 secs)
.
Junction Line Ring Assignment
.
Junction lines incoming ring can be set in the Direct ring modes
:
Direct Ring Mode
(Calls land on Operator or def ined extensions in Simultaneous Ring mode or Round Robin
Ring mode)
Direct Ring Mode (Simultaneous / Round Robin)
Simultaneous Ring
In this mode, incoming Junction lines ring on one or more Extensions.
Incoming ring of Junction Lines can be programmed separately f or Day and Night modes as described below:
Dial #
0000 + 3 J M 0 + N
1
+ N
2
…..+N
6
#
Where J = Junction Number (1, 2)
M = 0 f or Day mode/ 1 f or Night Mode
N
1
….N
6
= Here N is the last digit of Original extension number
(Not the Flexible Number)
Round Robin Ring
In this mode, the incoming Junction call lands on one extension. If that extension is busy or d
oesn’t respond within few rings then the call
shifts to another extension.
Programming
:
Dial #
0000 + 3 J M 1 + N
1
+ N
2
…..+N
6
#
Where J = Junction Number (1, 2)
M = 0 f or Day mode/ 1 f or Night Mode
N
1
….N
6
= Here N is the last digit of Original extension number
(Not the Flexible Number)
When all assigned extensions are busy
When the extensions assigned f or the Junction incoming call are busy, The assigned extension when busy, will hear a
waiting call beep af ter every 5 seconds. On f lashing ext will get connected to incoming junction call.
Default:
All the Junction Lines land on Extension number 601 and 602 in Simultaneous Mode.
.
Junction Line - Enable / Disable
.
To Enable Junction Line, Dial #
0000 + 060 J #
To Disable Junction Line, Dial #
0000 + 061 J# Where J = Junction Number (1, 2)
Note: In def ault Junction Line is enabled.
.
Junction Grouping
.
Two set of Junction groups can be made. One group can be accessed say by dialing 0 and the other group of Junction
lines by dialing 8.
To allot group 0 to a Junction= Dial #*0000 + 50 J 0 #
To allot group 8 to a Junction= Dial #*0000 + 50 J 8 #
Where, J = Junction Number (1-2)
.
Junction to Junction Forwarding
.
There are 2 types of Junction to Junction Transf er:
1. Incoming Junction Call on Ext to be transf erred to another Tel Number/Cell number.
2. Making 2 Junction lines talk to each other while Ext remains out of the conversation.
Incoming Junction Call on Ext to be transferred to another Tel Num ber/Cell number
Any of the Extension can f eed in a Telephone Number or Cell number on its extension whereby the incoming calls on its
extension would get diverted to those numbers.
While talking a tone will be heard af ter 2 minutes and if
is pressed then the call would get extended f or another 2
minutes. Like this user can keep extending the talk time. If
is not pressed then the calls will disconnect. If user wishes to
disconnect in between then # need to be pressed.
